I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
Currently working on a project for a company that uses your product.
Does Nordic use a certain style guide, or do they have a style guide internally that I could...
Hi Folks,
I'm using the Custom board with nRF52 and temperature sensor .
I'm trying the Experimental_App_Peripheral_Blinky code in the custom Board but i couldn't able...
Equipment: PCA10040 DK with SDK14
I'm currently having the same issue described in this post.
Essentially, I can program and build my project correctly in Eclipse, but...
Hello,
I have the following questions about the SAADC of nRF52832:
The relationship between ADC code and result.
For 0.6V reference, 12-bit resolution and single...
I'm writing an Android application that connects to a physical device via BLE. Android app will act as peripheral role while the device is central (with a BLE113 module inside...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
Hello, I am working on optimizing the power consumption of our application.
I have got two design decisions that I would like to ask for some advises and opinions on.
...
hello,
I uses NRF51822 to make a beacon with RTC.
When it works initially, the churrent is small about 330uA，but after a few minutes it becomes 1.1mA and stable.
I donn...
Hi,
I'm using CircuitMaker and I tried to import NRF52 reference implementations .PrjPcb files. Unfortunately CircutMaker does not support Altium PCB 6.0 files yet, but...
Hi,
I've recently bought a bluetooth module with a nRF52832 module for my new project (Module: EYSHSNZWZ from Taiyo Yuden). The problem is that I have no experience in embedded...
When I need to implement the functionality of bootloader_secure_ble, I need to produce the micro_ecc_lib_nrf52.lib library file in the following way. Why does not this library...
I'm building home temperature sensor with custom pcb design. I'm using balun( 2450BM14E0003 ) and chip antenna( 2450AT42B100 ) from Johanson Technology. Beacon works and it...
Hello everyone, here I have a problem when I learn to use beacon on 51822.
The steps as below:
I have a 51822 board, it can boardcast normally, and communication OK...
Hi there,
I was trying to use the bootloader_secure_ble example from nRF5_SDK_14.2.0 but it didn't work out of the box... I wasn't able to detect the board from nrfConnect...
How can I use nrf 52840 PDK to program custom PCB made using nrf52840 soc and reference circuitry suggested in datasheet, Circuit configuration no. 6 ?? Is there any software...
