Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
Hi all
The errata sheet V1.8 states that the errata 143 applies also for the Bluetooth Low Energy mode. Does that mean that the BLE stack of the SoftDevice S132 is also...
Hi,
I am using nRF52832 DK and other same custom board, sdk v15.0 with SES IDE. My application like this:
For ble peripheral used example ble_app_uart and for central...
Hi Sir,
In my system (windows 7), I had install the GCC 4 .9 2015 q3 for SDK 14.2.0/12.3.0.
As reference the release note of SDK 15, the GCC upgrade to 6-2017-q2-update...
Good Morning Team, Hope your day is going well! Can you please provide the Full Material Disclosure (FMD) document for below part since I could not locate it on website. ...
Hi, I am merging the multilink example and the CDC ACM example in SDK15.
However, if you merge and run it, it will continue to fail.
Here is the source.
I have...
Hi, i am using a model based on simple_on_off model to send custom messages.
For now provisioner and client are separated as in the V2.0.1. I tried to combine them first...
Hi,
Is it OK to use the Nordic Semiconductor ASA (0x0059) ID for broadcasting data in the manufacturer specific data field?
If so is does Nordic provide a specification...
Hello
For the BLE Mesh 2.0.1 demo i bought some nrf52840 develboards. Then i write the demo with "python scripts/quick_start/quick_start_demo.py" to the nrf52840 develboard...
Dear Nordic Team, Thanks for supporting.
I want to know the possible for mesh network concept with nRF52832 (PCA10040). If possible means guide me for startup.
Regards...
HI!
I'm a happy owner of two nRF52840 Preview DK board (v0.9.3). I'm considering to change their chips to production versions. I found that schematics and PCB layouts are...
Hi,
We are using nRF52832 for one of our central device. Our peripheral is also based on nRF52. We are facing issues while scanning for the peripheral from the central side...
