Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
I am using the ble_peripheral template that comes in Nordic SDK 8.1. I setup uart logging and also debugging with the following lines of code:
void assert_nrf_callback...
Hi, We are trying to connect a LED to one of the GPIO of nRF52840, we would like to know how to connect it. Connect it such that the nRF52 GPIO sink current or source current...
Hey, I am using WT51822-S4AT module and want the nrf51822 to connect to phone. I don't have nrf51-dk. I am using stm32f0-discovery kit. Can it be done using that kit? I searched...
Seems battery reads are not consistent in thngy52 2.1.0 software.
Observed a ~4% difference in the consequent battery reads. This difference is high (upto ~40%) if the thingy...
In the recent past, I used a SoC in which GPIOs could be configured as "open drain", that is in which there is an internal transistor where the SOURCE is grounded, the DRAIN...
Hey,
I'm using nRF as a SPI slave with a Raspberry Pi. I'm seeing that even at ~3MHz SPI frequency, my first byte transferred gets corrupted. I have a test setup where...
I am using nrf52 with s132 and armgcc
As I add functionality to the code I get to a stage where it fails. Linker runs OK but the result fails to execute.
The observable...
I am currently working on a BLE beacon project on nRF51822. Using SDK 12.3.0 and s130. The device has to advertise URL, advertising name and output power level. And these...
I am trying to control a current measurement chip (DDC114) that works with a protocol that is close (enough) to SPI. It has 2 channels, s.t. it can be read out and integrating...
I am attempting to run my first bit of code on my Nordic nRF52-DK and every time I have attempted to upload the code to the board, the board disconnects in the middle of the...
Hi, I'm using nRF52832, SDK13.0.0 as peripheral.
My iPhone app(my company's) makes connection without problem.
But Android app gets connection fail when it tries to connect...
Hi @ all,
We tried to enable debug log for lwIP module by setting NRF_LWIP_DRIVER_CONFIG_LOG_ENABLED in sdk_config.h to 1.
This threw two errors during the build process...
Hi @ all,
by working on a MQTT project using IoT SDK v1.0.0 (SDK v14.1) we discovered problems with TCP packets not being transmitted.
Using lwIP, transmitting TCP packets...
