Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Does the following SOC,
nRF52840
nRF52832
nRF52810
have sub 1-ghz RF ? by reading it seems that it is having the 2.4 Ghz RF.
I was looking for 433 MHZ or 863...
Hi.
I want my peripheral, an nRF52832, to accept a connection from the first peer it sees and bond with that peer, and thereafter accept connections only from that peer...
Hello
I am using sdk version 14.0 and softdevice S332. I successfully tested on the nrf52832 board using the ant bsc example.
However, when we put the code on our custom...
Good evening,
I am trying to implement queued write (long write) into ble_app_uart example. I am using s110_v7.1, nrf51822(pca10028), can not find version of sdk it is...
I have enabled radio notifications (through sd_nvic_ functions). When sd_ble_gatts_hvx() (notification) is called once, I've noticed two radio active-nactive windows occur...
Hello,
I have a bootloader with a low power wait for power button on startup.
When I do a BLE DFU update of bootloader + SD + appli, the Nordic smartphone application...
hi
I have a application use NRF52832 to scan beacon's advertising and write the advertising data into NRF52832's advertising.
I found the working current is nearly 3mA...
Hello,
I am useing NRF51822-QFAC in my BT bridge project; Now I need to design the matching circuit; there was some recommended matching circuit in the datasheet(11.3--11...
I have a central device that uses BLE to scan for a specific device (there is only a single device it can bond with). Right now it checks the UUID and the mac address of all...
my device giving output as square pulses.but would like to control current from the range 50uA to 500uA of square pulses.how to calculate it. can someone help me
Hi,
I have a question that Product Specification v3.1 of nrf51822 describes Flexible Power Management: 2.6 μA at 3 V ON mode, all blocks IDLE. But, in the same place, NRF52832...
Working on migrating my application from sdk 12.2 to sdk 14
except for some flash issues most of it seems to be working as before, except I notice this message in jlink:...
Hi,
I'm using SDK 14.2.0 flash_fstorage_example_s140_pca10056 with SEGGER on the nRF52840 Preview DK.
As you can see the basic example not working, what I'm writing...
I got the ble_app_lbs example working using SDK 8.0.0, and am now trying to integrate it into my existing project which was based off of ble_app_rscs using SDK 11.0.0.
...
Hello,
I am trying to intergrate the blinky, timer, and UART examples.
Blinky and Timer examples seem to work fine.
When I added UART, linker error starts to show up...
