Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
Is there any way to invert the PWM behaviour easily? I'm trying to develop firmware that will run on the DK52 (LED active high) and my custom board (LED active low).
I...
Like it says in the title. I'm working on an embedded application where lifetime is pretty important, so I'm trying to get power consumption down as low as possible. I don...
I have Rx sensitivity issues when DCDC is enabled
The 52832 datasheet shows these connection:
DCC: 10 uH,
DEC4: 15 nH
When switching both inductors I get better sensitivity...
Hi, I am have been using PPI to control SPI transfer in response to a GPIO interrupt.
The PPI initiated SPI transfer that reads an external device's register A and I would...
while the ble_uart example is a great resource of information, i have a need to completely separate the ble nus data in / out from the hw uart code
using sdk 14.2.0
...
Hi everyone,
So I've this arduino code that utilizes the I2C library and made some convertions to it to work with the nrf52832 in the segger embedded studio and when debugging...
Hello, I'm trying to migrate an Atmel project to nrf51822 chip.
Now, in the original project there were 2 CB arrays registered, one dealing iwth GATT one with GAP:
a...
hi,
I am working on nrf51822 chip and using sdk11.0.0 sdk,softdevice (s130 2.0.1) .I want to send 4Kb of data in a packet from the central device and on the other side my...
Dear all,
We have just purchased "nRF52840 Preview DK" kit for a project that connects BLE SoC to Linux host machine.
I have just realized that Connectivty example from...
Hi,
I managed to get fds to store some information in nrf51dk for persistent data storage. I would like to check if the data is still available in the chip after power...
Well, I have question for this SPI connection problem.
anyway,I have nRF51822 core board using adxl345 with SPI connection. that connect SDA to P5, SDO to P6, SCL to P7,...
Hello,
I understand the nRF9E5 is programmed through the externally attached AT25320B, ok. I understand three bytes are appended to the .hex file for the 8051. Since I...
Hello Nordic team,
I just post a message here to take the temperature, and your respective engineering opinions about that…
It's been a few months that I work on the...
I'm using SDK 14.2 (not really relevant I guess) on an nRF52832. The application requires a greeting to be sent to the remote through NUS as soon as a connection is made....
