There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
When Going into Sleep, I see peaks of 12mA every 30ms (see image) I'm assuming I can adjust that changing the connection interval settings. I have my Connection intervals...
I'm having some issues with the freeRTOS example in SDK 15. I've always seemed to find a hardfault which limits the MTU size to 176. Now when I try and set the connection...
Hi,
I have a question regarding fast/slow advertising
I'd like to advertise for 180s using a 100ms interval, then switch to a 1s interval, preferably for ever. I set...
I would like to use ADXL335 accelerometer in this nrf52832 custom kit Hackable . I don't have a J-Link but i have this custom programmer Bumpy which is based on the Black...
Hi,
How can wake my nrf52832 based module from system off sleep mode. i am using ' nrf_pwr_mgmt_shutdown()' / ' sd_power_system_off (); 'function to put the device into...
softdevice 6.0.0 SDK15.0.0 How do I use ble_app_hrs sample code add buttonless_dfu function? I flow the steps, but I am fail. 1. In ble_app_hrs project... add nRF_DFU folder...
Hi Support team,
In this application note, solder paste type 4 has 25 to 45 micron particle size range while IPC J-STD-005 as attached stated type 4 has 80% Minimum between...
hi.
I used mergehex.exe to combine the hex of softdevice, bootloader, and application into one, but the board is in DFU state and the application does not start.
I am...
Hi! I'm developing on nRF51 with SDK 11 and trying to extend our application with buttonless BLE DFU support. Due to limited flash memory, we could only use single bank ble...
The website is broken for me, and I see a sequence of orange pop-up messages saying "An error occurred. Please try again or contact your administrator."
When I use master control panel to scan ibeacn, I find "Complete Local Name" in below picture,
How to set the "Complete local name" ?
I heard someone says set in the...
Hello,
I've now been looking for a while but haven't yet found anything working to programmatically unwind the call stack when working with the nRF51 or nRF52.
Basically...
We are completing the design of a PCB and have a mounting/assembly issue with the NRF52840. We In looking at the mechanical spec on your datasheet w find that A row of 24...
