Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Once GPIO is pressed (shorted to ground), I want to change the value of UUID or Major/Minor number
If not, the device will continue to advertise the previous values
Hello,
I am working on a custom project with nRF52832 using SDK14.2 and s132_nrf52_5.1.0.
Now I am trying to configure and use RTC2, and face the problem that ble_stack_init...
Hello everyone,
after hours of python module installation, I was able to run the PPK with PCA10056. I have cut the SB40 and used an external pwoer source with 2,5 V. I have...
Hi I have two problemes, I do not know where to start, so if someone has an example, I would like to see it. The first thing is if someone has an example about using pwm to...
When registering a base UUID with the SoftDevice via "sd_ble_uuid_vs_add", a uint8_t is returned which (per the ble_app_pwr_profiling example) is intended to be the "type...
SDK 14.2
I try to use the watchdog using this code
static void nrf_wdt_event_handler(void) { NRF_LOG_INFO(">>> nrf_wdt_event_handler") }
int main(void) {
...
nrf_drv_wdt_config_t...
Hello , I am working on the development kit nrf52, i want to know how i canget the value of the RTC overflw and then how i can reset the RTC to zero.
thank you in advance...
We are developing a React Native mobile application for iOS and Android, making use of the react-native-ble-plx library to interface with the BLE UART service from the examples...
I'm running various example programs, and would like to find documentation for the functions I see them calling, for example nrf_drv_saadc_init...
Where can I find documentation...
Hi,
I have connected my custom pcb to the development kit at pin 19. When i use jlink commander, the board is detected properly. I use nrfjprog to dump the softdevice(Using...
I'm trying the get the development kit of the nRF52832 (PCA10040) displaying a floating point value. I read several postings of this problem, but non of the suggested solutions...
Hi, I'm having an I2C read lock-up issue similar to those described here , here , and here .
I'm using SES, SDK14.1, and an nRF52382. The only other component on the I2C...
Hi,
I have a custom board with nRF52832 SOC and temperature sensor in it.Interface Between the nRF52832 and Temperature sensor is I2C.i have to see the data through the...
Hello
We are currently making STN1170 based OBD II scanners with the nRF52810 for communications. The product is stable and available for commercial deployment, however...
