Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I am new to BLE and Nordic. (I am not new to Embedded Systems.)
What I am looking for:
Find a hardware and an example for BLE that I can adapt to my simple needs, e.g...
Wow need a bit of help the Thingy worked once did the update and now it is totally useless its a breathing blue light emitter? Nothing can see it MacBook, iPhone and no apparent...
Hello - I tried looking for my answer here but didn't really get what I need. I'm also relatively new to all of this.
I purchased the Adafruit's nRF8001 bluetooth module...
hi
i am using nrf52 dk wiht IAR embedded workbench IDE ARM 8.20.1
i want to disable the attach to running target from my device HZX-52832-S01A.
which bit i have to turn...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit (PPK).
I want to change the voltage supplied to nrf 52 arbitrarily.
I used the following case...
Hi everyone!
How to change erase range in DFU during application upgrade ? I have some data saved in flash (by psotage on 0x0007e000) and I don't want to lose them after...
Hi,
What is the advantage of using a Bluetooth SIG defined profile over a vendor specific profile? For example, if we want to transfer battery levels, can we define our...
Hi again,
Hope everyone had a great Christmas.. I did, but Santa also gave me a litte issue with my nRF52-DK..
I using a modified UART example, I have a 5min repeating...
Hello,
Basically my arrangement of NRF network is one receiver and multiple transmitter consider example 1:40 and they all configured with same address,bitrate, checksum...
Hello,
Is there a demo project that contains RTC function with softdevice.
I called the lfclk_config() and rtc_config() function before softdevice initial in main(), but...
I am using nrf52832 chip. I will be receiving time in isoFormat.
I am wondering how convert the iso format to get the date and time in my C program.
I am not using any...
Hi,
I'm develope some sensor with arduino primo, which use nrf52832 as a primary mcu.
I want to measure battery voltage level,and i find some example like:
devzone.nordicsemi...
I am using nrf52832_xxaa with SDK v11.0.
I have a requirement to write into UICR register APPROTECT to set its value to 0x00.
Is it possible?If yes, please provide a sample...
