Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
Finally, I managed to compile ble_beacon in segger.
However, here's what I can not understand.
Using either Segger -> Target -> Download File
or RKNRFGO I managed to...
I got beacon which use nRF51822.
I need to get radiated pattern diagram as attached picture.
this is to get KC certificate.
How can I get information? beacon maker...
Hello,
I'm using a module based on the nRF52810, the Fanstel BT832A. I'm running the basic "ble_app_beacon" firmware from the "nRF5_SDK_14.2.0_17b948a" SDK with a few changes...
I spent a few hours trying to change the base UUID and handles of the attributes of the Blinky peripheral app, just the one service and the button and LED characteristics...
I have couple of nRF51422 boards, nRF5-SDK-for-Mesh (v. 1.0.0) and good will to demonstrate some simple multihop mesh.
And I want to write some data to the flash, but operating...
Dear Nordic,
I are using nrf52832 to develop a product that needs FCC certificate,
We use a PA and can increase the output power up to 20 dBm and it
seems that is lower...
Hi guys, I’m doing several tests with my new RedBear BLE Nano v2 board based on nRF52832 using the RedBear library, but I found a problem with reading Notify Characteristics...
Hello,
I need time synchronization between the two devices. At the same time I want to use the standard means of bluetooth, synchronizing the clock of the connected devices...
Hello,
This is the first time I try to implement DFU to update my simple application OAT via BLE on the nRF51 DK.
My simple application is a simple peripheral which...
I have a GPS over UART to a nrf5283. For debugging the GPS, I'd like to passthrough UART from my PC to the GPS. I know the nrf5283 only has one UART. Is there a simple way...
First about my setup: custom devices with NRF52832 chips (SoftDevice 132 v.4.0.2), android smartphones Nexus 5x and 6p.
I'm trying to connect as many BLE devices (peripherals...
I'm working on a custom board with an nRF52382 connected to an IMU over I2C. The IMU provides 2 separate interrupt signals, and I would like to route each of them to a separate...
Hello,
Today I've a strange behavior of nRF51 DK (everything was working ok until today, the last things I did was to reset the J-link FW after a total erase of the board...
