I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I read a lot of questions but problem still wasn't fixed. Random disconnect have the period 5-10 mins. The problem with s132 or s130 v2.0.1 and LG G3 android 5.0....
Does anyone know when will ANT SoftDevice be available for nRF5 SDK v15? Accordign to https://www.thisisant.com/developer/components/nrf52832#tab_protocol_stacks_tab, only...
Hi
I try to communicate with my NRF24L01+. For this, i have connected a mikrocontroller to my Module. Actually i am using a small piece of code, which allows me to send...
Hi,
In my project, I use button for put on the microcontroller in sleep mode. I implemented one timer that when I press more of 5 second the button, the micro call sleep_mode_enter...
Hi,
I have included in my code the code from the twi_scanner example as a starting point for using TWI in my board. When compiling, I get the following error:
../.....
hi,
Please Refer Light Switch Client Example in Mesh 2.0
I would like to know Code where and in which File the UUID from the unprovisioned Node is captured ?
Thank ...
Hello,
What is the switching frequency of the buck regulator integrated into the nRF51822?
The characteristics of this regulator do not seem to be explained in the documentation...
I'm following the Custom BLE Service Example , and using:
Segger Embedded Studio Release 3.34a
macOS 10.13.4 (aka High Sierra)
nRF52 DK (PCA10040, nRF52832)
nRF5_SDK_15...
Hi,
I am investigating an alternative to an implantable device that currently uses NFC.
The device range would only be about 3m and the data would only be transmitted...
this packet is capture by wireshark .I use nrf51822 and sdk12.3 connect Balance car,but the packet not have LL_VERSION_IND, LL_FEATRUE_REQ、and LL_Connect_UPDATA_REQ these...
Dear Nordic Team,
Thanks for supporting.
now i am workwith secure dfu. I followed this link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure...
hello
I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice.The nrf go studio can not detect the nrf52832, but the keil...
I was facing some issues getting PWM peripheral work on my custom nRF52840 board. And then I tried the pwm output on P0.08 instead of P0.06 and the signal came out just fine...
We're developing a new device for a regulated market (medical). As such, we need to have control on what third-party software we're using, and how it is working. While starting...
