Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
Hi, I'd like to evaluate Linux device driver for nRF7002; refer to 315431 , I'd found this requirement had been reported one and half year ago; based on 315431 , I have a...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
Hello,
I study the UART Central-Peripheral example (NUS) out of the box based on Visual Code IDE. I would like to understand on the Central part:
Where exactly in code...
Hello,
I have a ble mesh with a nRF52840 Eval board and a certain number of nRF52840 dongle nodes.
I communicate via mesh Chat between the Eval board and the nodes.
...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
Hi Nordic team,
I'm using the nRF9160 DK with nRF Connect SDK v2.9.1, and trying to run the coap_client sample to send a GET request to the public CoAP test server at coap...
For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
I’m curious about the current consumption.
Based on the nRF52840 chipset, I found that the current consumption in both sleep and TX states varies depending on the TX power...
Hello,
I am currently evaluating options for integrating Bluetooth Low Energy (BLE) functionality into a medical-grade device that requires time-sensitive communication...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hi Sir
The npm1300 allows setting the default voltage using resistor values as shown in the table below. However, if I want to set the voltage to 1.05 V using resistors...
I am working on synchronizing RTC timers on several nrf52832s and i would like to have a single clock clocking all the RTCs on all the boards. I understand that the LFCLK...
