I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello
I need a second UART, one for adebug long on the PC and the other for communication with another device.
My application is based on NRF51822 which has single UART...
Hello,
I am attempting to achieve UART Serial Communication with the ADAFRUIT FONA 808 Board, this has a SIM808 Cellular Modem.
I have attempted to re-purpose the examples...
I'm in the process of developing a BLE-based system in which a series of sensors will need to sequentially go through a pairing process with a host computer. There could be...
Hi,
We are using ARM mbed compiler and the nrf51822 which has 256Kb of Flash. We are trying to see what is the maximum bonds we could store on the nrf51822 as this is the...
I tried to set up the ANCS example. It works fine. But how is it possible to set a higher MTU. I set the NRF_BLE_GATT_MAX_MTU_SIZE to 247. But the Log says after a connect...
Hello, somebody help please.. I want to implement Machine Learning using tensorflow, KNN or whatever is good for my module, that consist of Bluetooth Low Energy nRF51822 type...
I want to start with the following nRF52 ADC example .
While doing so, I found that the example is built on SDK v13 and SDK v13 doesn't have Seggar Embedded Studio support...
Hi
I successfully merged SDK for mesh v1.0.0 to nRF14.2 by following the example in https://devzone.nordicsemi.com/f/nordic-q-a/28936/merging-sdk-14-2-with-mesh_sdk .
...
nrf52832
SDK 14.2
My application is locking up, and finding the cause is proving to be difficult. I've enabled DEBUG and DEBUG_NRF and included the hardfault library...
I have an application that requires talking to 21 sensors wirelessly. The bandwidth required by each sensor is relatively small - roughly 2KB/sec. The sensors need to talk...
Hello,
The mesh lightswitch on/off example only calls 'sd_app_evt_wait' in the main loop.
I'd like to use '__WFI' instead. (Im combining some code with mesh, and i'd like...
Hello,
This case is a part of a private case. Unfortunately havent responded for few days. I believe he has days off or something, therefore I am willing to receive help...
Hi everyone,
I design own boar with nRF52810 SoC. But i dont know how to programming external. Which pins are using programming? SWDIO and SWCLK pins using programin i know...
I want to establish a BT network system which includes one pc as a central node, and 32 client nodes. I want to collect 32 client's sensor data concurrently via BT. At pc...
