Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Hi
I am working on a design using an nRF24L01+ in a circuit also consisting of an ATMEGA microcontroller and a H-bridge motor driver driving a brushed DC motor. The whole...
hi all!
I would like to ask the DCDC and LDO two modes of choice. My product is a watch, it uses the cr2032 battery dropped to 2.5v by an external LDO to 52832 power supply...
Hi,
I am using nRF52832 development kit PCA10040 V1.2.1 2017:38. I am able to successfully run nRF_Examples\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral...
hi,
I am using PCA10040 v0.9.0 Nrf 51 DK.
In schematic I am not getting connection for programming connectio n .In sheet 4 of 5 at the USB Connector connection signal...
Hi,
I m trying to develop an linux-application running on node.js to communicate with a nrf52 device. I m using the noble-module ( noble ) and a usb bluetooth-dongle. ...
Hi,
Is it possible to connect nRF905 to nRF51822 via SPI, add ShockBurst code nRF51822 and then use alternately/simultaneously Sub GHz and Bluetooth communication?
I'm...
Is there nRF Connect or similar program that enables development of BLE applications for Windows 10 (using native BLE API - ideally universal windows platform)?
At a connection the call function app_error_fault_handler()
with parameters
m_error_data.fault_id = 0x01 m_error_data.pc = 0x14DBE m_error_data.error_info = 0x0
Is not...
I'm trying to configure UART functionality in my program, and in the event handler under APP_UART_DATA_READY I'm missing bytes that I should normally have received. The code...
Hi,
Is possible to program the nRF52832 with a target voltage between 1.7V to 3.3V? I'm thinking to power supply the MCU with a pair of AA batteries in series.
Thanks...
I am using the "Nordic Uart Service", example to create a simple serial console which allows a user to change settings such as tx power, advertising intervals so that different...
As in the circuit diagram attached where the pin resource is insufficient For one Pin (AMULTI), I design gpio for Button and analog input as 2channel. (This switch uses the...
Hi DevZone,
I am going to apply a Arduino CAN bus shield onto nrf528400 preview DK. I was integrated this shield with Arduino board and a 3rd party BLE module. Now, I am...
I'm basing my PCB design on Nordic's reference layout. The product I'm developing will only be used for research, and is basically a one-off design. How closely do I have...
Hello,
I am using the NRF52832 for advertising every 10s.
However while entering the sleep phase, I noticed some glitches while measuring the current. You can find attached...
