I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I need to upgrade and existing nrf51 S110 system based on SDK 8.x to something that supports the same functionality and also supports both a nrf51 (during the transition)...
I am working on a project where we are using a nordic bluetooth chip and connecting it to a RS485 Bus using UART with Baudrate 115200. The messages sent from the Bluetooth...
I want to experiment with BLE Mesh. I have several BLE400's with nrf51822's. I want to use these as mesh nodes. I want to get the nrf52-dk to use as an interface node. Can...
I recently downloaded Segger's Embedded Studio to compare its performance and ease of use with IAR Embedded Workbench. We have a kickstarter version of IAR for ARM which has...
hi,
i am using nrf5 sdk 14.2.0 ble_app_uart example with keil v5 IDE and i am doing coexistence with nrf5 sdk for mesh v 1.0.1 for nrf52832 mcu.
a have done all steps...
I use nRF52840-Preview-DK PCA10056 v0.9.3, SDK 14.1.0.
I would like update bootloader, but i have any problems.
I do these steps
1.eraseall 2.program softdevice 3.load...
May be I just did not fined a good reference manual for the software, but it really frustrating me to try and understand from examples.
Is there some guide which take a...
When P0.18 is configured as the RESETn pin, is there a pull-up enabled?
In our design we have an external CPU driving the nRF52 RESETn line.
We have a pull-down on that...
Hi all,
I was wondering if the information in the documentation is the right, I was looking for the Memory map for the nRF52 when using the SDK13 s132 v4.0.2, but on the...
Hello,
Could you please indicate where TXPOWER is defined in the "ble_app_beacon_pca10040_s132" code example ? If not defined, could you please indicate what is the best...
Hi,
we are currently planning how to productize our IOT module which is based on nRF52832. We most probably use pre-flashed SOCs, but the we should be able to read Device...
I am trying to implement 128 bit uuid service and charachteristic and I am getting error 4(memory error) from
line 10: sd_ble_uuid_vs_add(&m_midi_service, &midi_init); ...
Hello. Devzone engineers
I'm testing Nordic_Uart. I have some issues.
UART\s data not sent to android. Android app is nRFconneter and Example is nRF5_SDK_14.2.0_17b948a...
I'd like to be able to enable/disable the S140 SoftDevice multiple times during operation (SDK 14.2.0). To achieve this I'm using `nrf_sdh_ble_enable` and `nrf_sdh_ble_disable...
