Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi All:
I met a trouble， i don't slove it. i need help .
sdk : nRF5_SDK_14.0.0 S132
hardware: nrf52832
base multitole dev.
nrf52832 as master to connect mobile by ble...
hi everybody
SDK:14.2.0
CHIP:nrf52832AA
example: ble_app_uart or ble_app_beacon
board:my board,not DK
My board program into ble_app_uart or ble_app_beacon hex,it...
What's the maximum time between random numbers being generated on the nRF52832's RNG? The datasheet just says
The time needed to generate one random byte of data is...
Hello everyone,
I remember doing a project with PCA10028 board and S110 SDK a year or a year and a half ago. Now i want to do another project but all my materials which...
Hello,
I am writing this question in reference to this question . I was asked to be more specific about my question by my colegues. I do understand that this is a duplicate...
Hi,
I checked the flash_fds example. I could not tell the address it tries to access to. Is there any way I can find the address? Can I limited it to a certain address range...
According to this article, https://www.nordicsemi.com/eng/Products/Bluetooth-5, it appears that the nRF52 should be able to support standard BLE at 2Mb. However when I look...
Hi Nordic
I am using sdk 14.2.0 version and s332 soft device. Now I have completed the bicycle speed cadence code that works with ble_ant. It worked well as I wanted. But...
hi,
I am a fresher .I am asked to do the communication between nrf51 D K and moblie phone( nrf connect app). Can anyone provide me a sample code and required documents to...
Hi
I am using SPI to talk to an LIS2DH with an NRF51822. I have merged the SPI Master example with the ble_app_rscs example and as soon as the ble advertising begins, my...
nRF Connect has no serial ports to connect to. I've looked in /dev. No unusual tty or cu devices listed. I've checked the forums. Mentions is made about Segger link and "...
Board: custom board
Mesh SDK: V1.0.0
Softdevice: S132
IDE: SEGGER Embedded
BLE: nrf52832
When I test the steps specified by “Interactive PyACI”, I can control client...
Hi,
I have spent a couple of days trying to find formal documentation on how to update the nrf SDK. I am currently on 11 (as keil pack installer states the version of...
