This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am using PCA10040 devkit and SdK11. Our application is to advertise at an interval of 100ms. Also, our application wants to spend most of the time in sleep mode. Currently...
hello , i am trying to imblement system off or system on in one of the ble central example 'ble_app_blinky_c' , i tried to refer to this example 'ble_app_template' but if...
Hi all ,
I am beginning with DFU . I complete bootloader_secure_ble and can update new firmware (application) to my NRF52832 kit via Android . And now, I have 2 kit NRF52...
hi team,
i am wondering that lot of questions regarding gps and wifi interface with nrf52 is there. why nordic is not supporting with libraries and examples for gps and...
Hi there,
I read that the nRF52840 has a maximum data throughput of around 1.3~1.4Mbps . I also read that when configured as a central it can support up to 20 concurrent...
Hello,
Can anyone point me to a good example for Polling mode using serial library?
I'm looking for an application in which I can poll the serial port for data. I went...
I'm investigating the flash usage by the peer manager to store bond related data. While I haven't had a chance to fully investigate how the FDS and fstorage modules work,...
Hi,
We have a need to have a Nordic app for nRF51822 which both serves as a beacon and also offers a connectable service.
It's my distinct impression at present we cannot...
Hi,
My setup :
nRF52832
Soft Device S132 v5
SDK14.2
My use case involve me to send data to to a central device at 50 meters. I need to send only a small data...
Hello everyone :) , I work on a project initialy configured for a PCA10040 board and I would like to use the debug with my PCA10056 board but unfortunatly the debug doesn...
Hi
For some reason I get stuck in softdevice at 1EA7A when a send some random data to my phone also I notes that function sd_ble_gatts_hvx return 3401
PC = 0001EA7A, CycleCnt...
I am trying to connect thingy as peripheral and many smartphones as central but i can connect only one smartphone by using thingy at a time.Is it possible to connect many...
[References]
In page 234 of nRF52832_PS_v1.4 it says "In both modes, the TIMER is started by triggering the START task, and stopped by triggering the STOP task."
In this...
I am trying to add a custom service to support a communication path in my project. The Nordic UART example gives a good place to start so, using that as a template, I have...
Hi All:
i met a trouble.
i want to implement a function that i can restore mesh device by uart cmd.
so , i add uart to light switch service demo, when i recive a cmd...
