Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
Hi.
I want to know the time difference between functions by using a timer instead of a difference. I've looked at app_timer.h, but it's hard to understand.
I do not need...
I am trying to use the ADC to take power measurements on an interval. I found an example to read the values out online:
void ADC_IRQHandler() { nrf_adc_conversion_event_clean...
I am designing a PCB using the NRF52832 and this antenna . The antenna design guidelines suggest ground clearance and direct traces from the NRF52832 to the antenna without...
I am working on a project which I wish to Paer between to nRF51422 devices and to use the auto reconnect between them. there won't be any display so it must be automatically...
Hi,
is it necessary to use internal regulator for NFC DC/DC or we can use normal internal LDO in design.
also if we need to use internal DC/DC regulator, what is the...
Hi, I have tried to find a solution for some time now in the Nordic Semiconductor forms.
We have been noticing a peak or a disturbance in voltage in every connection interval...
I have encountered a scenario in which my application is terminating the BLE connection via a call to sd_ble_gap_disconnect, while around the same time I receive a write request...
I'm able to successfully use peripheral/uart example to read the data from GPS module. I achieved the same by setting baud rate to 4800, and connecting rx and tx of GPS to...
Hi,
Question about FOTA (firmaware upgrade over the air).
I know that nrf52832 has 512 kB of flash, and the ble stack( softdevice ) has 136 kB , and the bootloader has...
Hi,
I put my NRF52 to sleep (POWER OFF mode) and configure it to wake on GPIO port event like so:
This GPIO is set up on a reed switch. Occasionally, the NRF52 will...
Hi
I found a strange issue on nrf52832. And I use nRF5-SDK-v13.1.0 .
When I assignment P0.7->SCL & P0.6->SDA, the twi function not working. But I change the assignment...
Today I read about the new nrf52810 and I want to know about its main differences with the nrf52832.
I see a lower power consumption for the 52810 vs 52832 and no NFC on...
Hi
Currently I try to migrate my software project (with SDK14.2, S132 (5.0.0), arm-gcc toolchain ) from nRF52832 to nRF52810 (with SDK14.2, S112 (5.1.0), arm-gcc toolchain...
