Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
In case the DSM metadata is changed compared to what is stored on flash, the 4.0.0 code is supposed to clear the flash from any configuration but this doesn't work properly...
Hello,
I'm pretty new to rtos and totally new to nordic's nRF9160. I've been trying to get this working all day and can't really seem to figure it out based on the resources...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader, the bootloader settings and the SoftDevice. Our product has a cellular modem to be able to perform OTA firmware...
Let say a situation where I want to know if the just connected client is the same as the one that was last disconnected, but if the client uses RPA than have somehow to try...
Hello,
I'm developing a BLE device based on nRF52832 and SoftDevice 112 using SDK 15.3.0. The device operates only in peripheral mode with only a single connection to the...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Hi,
We are evaluating devkit nRF52840-DK using SDK nRF5_SDK_16.0.0_98a08e2.
The application development is ongoing, based on examples\ble_central , using which we are...
Hi,
I have a multilink NUS central that connects to several NUS Peripherals using SDK 16.0, S140 (NRF52840 REV1). Currently I'm testing with only one peripheral, sending...
We're using the nRF52840 in our product.
We require to perform continuous scanning, with little power usage as possible.
We've seen in the Nordic specs and verified with...
Hi,
I'm using NRF52840, and I've developed a feature which bonds with NRF toolbox application. The problem is that when I'm using secured BLE, I can't receive any messages...
Hi,
I have an issue with getting a GPS fix from time to time under the almost same conditions. When it did not get a fix I could see in the UART log that the nRF9160 was...
Our custom board has an nRF52832. In our custom build system the application HEX and SoftDevice HEX are merged together into a single HEX file, this is achieved by Nordic...
We are in the process of getting our product through SRRC certification in China. I am using the radio_test example from SDK 11.0 for this. All is working fine.
However...
I downloaded SDK v16.0 and in the examples, I can't seem to find the dual_bank_ant_s332 folder.
It is present in SDK v14.2.0 in this path
...\nRF5_SDK_14.2.0_17b948a\examples...
