Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi, anyone call tell What is the acceptance rate of nrf52 series scanning
I'm used zephyr ble mesh example, One node sends, one node accepts, and the broadcast packet sent...
Hello,
When i build a project to the nRF9160 DK, the terminal shows output of the program. Everything works.
When downloading the merged.hex file to thingy91, then...
Hello everyone,
We are 4 students, who are developing a BLE mesh network to send data from a CANNBUS-simulator to a desktop. We have chosen to use the nrf52840 chip to set...
Hello,
I am using nrf52832 with SDK 16, I want to change advertising packet flags from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE(0x05) to 0x04 during run time how can...
Hi, Im developing an ac dimmer with zero crossing on mesh, but it flickers at low dimming levels, I even used the scheduler for the ble stack but it didnt help, what would...
hi, i am using nrf 52840 dongle , is there any support of AT commands to communicate with dongle .i want to communicate without using ui only by sending commands. if not any...
Hey Nordic Team!
My requirement:-
Sensor data----------------------------->nrf52832------------------------------>Raspberry pi 3 (via blue tooth)
Is it possible...
We are working on external RTC MCP7940(i2c) interfaced with nrf52840. Please check if drivers of the same for nrf52/51 are available or any implementation of CLOCK using MCP7940...
Hi,
I tried to add 3 characteristics and 1 gatt service to my NRF52810 using with development board with 10040e (I am using gcc compiler). Then I got a error which is saying...
we are considering using .005" thick stainless steel to provide better bridging effect across the opening on the board for the battery. This will provide more strength to...
Hi
I am trying to use an antenna switching board for AoA direction finding. I know that the RADIO controls 8 PSEL.DFEGPIO pins to control switching antenna.
1. Could...
Hi,
We want to use the NRF52810 without radio and we don't want to put the external oscillator to reduce the PCB size
I would like to know if necessary to have the external...
Hi,
Some time i could not put break points inside main for sample projects provided for nRF91, i tried clean build, erasing the flash 'nrfjprog -e' and evn enable the configuration...
We would like to use a Dongle based on the nRF52840 as a BLE Central communication via NUS to our product. The example in the nRF Connect Desktop does just wat we need on...
Hi,
I want to use none secure example on nrf5340.
The code can't run with ns config(uart didn't log anything),But it works fine with normal config.
How can I sovle this...