Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I'm using the nrf52840 and SDKv16 to interface with an SD card. An SD card block is 512 bytes. I would like to do this:
1. Get the card ready for a write (use blocking...
Hello,
Not a 100%, but in this Nordic video the nRF52840 might be using the Alexa Gadgets Toolkit. Alexa Notepad demo 2020 https://www.youtube.com/watch?v=CdLfg-6kQs0
...
Received our 52840 DK, loaded, via nRF Go Studio, s140_nrf52_7.0.1_softdevice.hex. Loaded, via IAR Workbench, ble_app_blinky_pca10056a_s140. I clicked to go button and whamo...
Hello. Nordic team.
Once again I had questions, this time related to serialization .
While the preparation of the driver is on the PC side, I am studying the examples...
I have an issue with reseting the board using a hard reset via an external button. The onboard development kit reset works, but I am trying to perform the same task using...
Hello,
I was reading the nrf_libuarte_async library, and noticed that in the
app_timer_handler -
calls the
local_app_timer_start -
again and starts the timer again...
Hi,
I use a 3rd party board from raytac ( https://www.raytac.com/product/ins.php?index_id=95 ) on my PCB and I have problems with a bluetooth low energy connection. On your...
Hello,
I'm trying to get sleep mode working on a nRF52840-DK with Zephyr or Mbed OS while using UART.
It is possible to achieve low current consumption in sleep mode...
I opened an example from the SDK 16 in:
nRF5_SDK_16.0.0_98a08e2/examples/iot/lwm2m/lwm2m_client/pca10056/s140/ses/iot_lwm2m_client_pca10056_s140.emProject
When I try to...
Hello!
I want to develop my own app, and the source code refer to proximity in nrf toolbox. Now, i have some questions:
1. What function in the source code of serverManager...
Hello
In my application, I would like to allow smartphone that are Bluetooth V5 compatible to receive more information in advertinsing packets from my devices (via the ...
Hi,
I want to optimize the transmission efficiency and thinking of sending larger packets than 2048 bytes of MQTT would help.
We have limited battery power, and looking...
Hi,
I am started working on nRF9160 Power Management. I want to power down all devices(sleep mode) expect motion sensor, Wake if motion is detected. I went through System...
Hi Team,
Can you please point me where I can change the compiler optimization level in SES v4.52 and I am using nRF9160 module.
Regards,
Praveen Palaparthi
Hi Team,
We are using the NRF52840 Device with S140 Soft device for our BLE applications. As part of this we have enabled the flash storage as well.
We are unable to write...