Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Theranica current solution already has a printed MIFA antenna and an impedance matching circuit that they have tested and is working very well.
they would like to keep using...
Hello,
One of the devices I have could not connect to AWS cloud. While checking if the credentials exist, I got the following error :
NRF_KEY_MGMT_CRED_TYPE_CA_CHAIN err...
Hi.
I'm trying to use nrf52832 twis as twi slave.
nrf52 DK(pca10040) is TWI slave (data receiver) arduino uno is TWI master (data transfer)
My code. (examples/peripheral...
Hello,
When I include in my code (Arduino IDE) sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE) on E-Byte 52840 module (E73-2G4M08S1C) power consumption increases to 30mA instead...
Hello,
Can the new nrf21540 extend the range of a nrf52840 in long range mode?
Late 2018 I developed equipment using the nrf52840 in Long Range Mode.
In some use cases...
Hello,
I'm new to nRF devices. I wanted to learn some basics with my nRF51 dongle.
But to my surprise the only free supported IDE is Segger and there is no clear step...
Hi,
I'm trying to write a program that i can get a different feedback from my development kit using ble_uart_app example, the idea is using switch case so i send different...
Hello Nordic team,
I am using nRf52840 DK and sdk 15.0 with SES IDE. Our application scenario is collect sensor data periodically as required customer and send it to server...
Hello nordicsemi devzone community,
I'm trying to use the SPIS peripheral example in the latest SDK to transfer data from an FPGA to a NRF52DK board. At low frequencies...
Hi all,
I am using PCA10059(nRF52840 dongle) to learn Nordic BLE solution. I start from \examples\peripheral\blinky project and Segger development environment.
Now I want...
Dear Nordic Support,
I'm working on a custom board, containing the NRF52840. I am using SDK 15.3.0 and SoftDevice s140 to implement BLE.
Recently I've bought the Power...
Our organization is evaluating nRF5340 for future connected products. We are working with a proprietary OS and using the Zephyr RTOS on the Application core is not a viable...
Hi, I'm using nrf52832, sdk15.3. I have 4 pressure sensors connected to a multiplexer (MUX) chip. And the output of the MUX is connected to channel A0 of the nrf52832. I use...
Hello,
I need to send a file of about 70KB capacity through BLE. I send each packet as 16 bytes, I get an error 19 after about 10 submissions. I have read the answers, and...
Hello：
We have a project under development which is about real-time wireless voice transmission using the nrf24l01P，We will send 96-byte voice packets each time. We intend...
