Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I want to disable and enable UART at runtime. I don't use DMA and interrupt.
I read this thread. https://devzone.nordicsemi.com/f/nordic-q-a/52496/nrf9160-uart-pull-up-and...
Hi.
I need to program for a set of NRF52832 with serial number from 403898368 to 403941418.
I am trying with nrfjprog --family NRF52 --memwr 0x10001080 --val %% --verify...
I am in the process of evaluating different BLE solutions for a project. The project consists of a pair of BLE-enabled devices which need to be able to go into dual-role mode...
Hi everyone
I don't really understand what the physical cell ID is. Is it a randomly generated ID created by the nRF9160 chip or a set ID within the cell?
As far as I...
Hello,
I am facing a really annoying issue when updating my SPI settings from the old nrf_drv_ towards the newer one nrfx , in SDK15. I am following the recommendtations...
Project context: -------------------- Server BLE for home trainer diy Target (Bluetooth server) : Bluefruit nRF52 The feather Library : BluefruitBLE Client : nRF Connect ...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) If I enable “Just works” and without...
I have a project where one device will be both a peripheral and a central. In the central role the device will connect to a sensor. It will act based on the sensor data. In...
Hi,
I am using nRF52840 Preview DK with SDK v15.3.0 and SoftDevice API v6.1.1
I want to set a filter in the ble scan to connect only to the specified MAC address,
...
I have been searching for hours on how to get past this. Can anyone help? This is my first time on here and I am new to SES, I am just trying to re-create a blinky example...
Hello,
Is it possible to use wireshark with the UBLOX evaluation board (EVK-NINA-B302)?
I tried but couldn't make it work. As I don't have a nordic evaluation board...
HIi
I am using the pc-driver-ble_py library to build a central in order to test a peripheral. At this point, I am interested in starting a LE ping and I saw that I should...
