Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
I am trying to send a string from the board through uart to the PC(windows) through usb-ttl. I tried using adruino and was able to successfully execute it. but when i tried...
Hi,
I've used the 'Getting Started with nRF9160 DK' tutorial to setup a development environment, I have a problems with loading asset_tracker project. My output:
Loading...
I understand there is a hard fault happening in the SDK. I am using SDK 15.3.0, I am not on a sdk example, but on a specific program I am doing I can't share. It happens a...
Hi,
I added a small shunt resistance to see current consumption of nRF52832.
I see current ripples when DCDC regulator is enabled, this ripples doesn't exist when DCDC...
1. We are running our nrf52832 based project on Eclipse and are able to compile, build and run the project on our target hardware. So far, so good.
2. Now, in addition we...
I'm working with the light switch server example and nRFMeshProvision example project for iOS.
How do you send arbitrary data to a board? I understand the provisioning process...
Hi,
I noticed that there are a few methods in nRF52 SDK v16 to blink LEDs:
Use bsp indication methods which seems based on app_timer;
Use led_softblink library which...
nrf52832, SDK 15.3
The average current consumption is 9.53uA in my system with SPIM. After I init another SPIS, the current consumption goes up to 478uA. CS pin keeps high...
Now I am using nrf9160DK for development. In my project, I need to use a random number generator and a highly accurate system time stamp. Is there an API that I can call directly...
Hello,
On nordic nRF9160dk I want to send SMS and receive the data from UART simultaneously. UART needs 3V VDD supply and for Sim card it is 1.8V. So how this condition...
Does SoftDevice S112 or S113 offer mesh support on a nRF52811?
The intended use is for an end-device running very simple app-logic. According to the SoftDevice properties...
Hi there,
I'm using nRF52840 dev kit board and v15.2 SDK.
I've set up a PWM using the PWM driver and is working well.
I'm frequently stopping and starting the PWM...
Hello everyone,
I have a nrf52832 (SDK v15.2.0) that is connected to a tablet via BLE. However, if I have several SPI transfers one after another, the BLE suddenly disconnects...
I am trying to retain the data on the board when it is transferred from my computer to the board through uart and once it is on the board through bluetooth to phone. Text...
I am now facing the following issues: https://devzone.nordicsemi.com/f/nordic-q-a/55975/about-reset-during-advertising
I call "sd_app_evt_wait" and go to sleep. Even when...
