Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
Hi
I'm migrating applications I wrote using SDK 17 to nrfConnect 3.0 with Zephyr.
I implemented USB devices with combined multiple USB classes. One of those classes was...
Hi,
In one of our future hardware designs, we have a MPU (running LInux) connected to a Bluetooth SOC over a serial interface (uart/spi/...).
Our first approach was...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As hardware I am using the nRF52840 Preview Development Kit. As software basis I use the ...
Hello, a couple of get-me-pointed-in-the-right-direction questions, if you don't mind.
I plan on creating a system with an accelerometer that talks SPI to my Nordic nRF52833...
Hi!
I read that your Thread stack uses a different 802.15.4 implementation than the MAC driver. Is it possible to intercept special broadcast data packets e.g. from energy...
Hi!
I started to modify the ble_app_blinky example. I need to increase ATT_MTU, so I modified NRF_SDH_BLE_GATT_MAX_MTU_SIZE. For this, I needed to increase the RAM of the...
Hello,
I'm using Mesh SDk4.0.0 and SD v7.0.1. I have tested the light switch client and server examples.
Now I want to add some more models for additional functionality...
Hi , i want to change the device name by connecting the device using nrf_toolbox , have a look at my code , you will get what i am trying to do . By the way i am using nRF52832...
Hello Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0, gcc-arm-none-eabi-7-2018-q2 in my customboard.
Recently, I am making ble central module.
I can scan and...
Hi, I have only one question: during the write or erase cycle using fstorage, the cpu is locked? Sofdevice, Interrupts and main application are working also during with flash...
I'm using FDS together with Flash manager, and checked if everything goes alright in flash.
As per doc, I set FLASH_MANAGER_RECOVERY_PAGE_OFFSET_PAGES to FDS_PHY_PAGES....
Hi, I just try to start with the spi master example (nrf5sdk/examples/peripheral/spi) on mus PCA10040 board. I'm able to compile&flash it. It seems to be running (LED1 is...
Hi ,
I working on the getting started assistant setup but got failure when verify the GNU ARM embedded setup , see the following log :
11:32:05.867
c:\gnuarmemb\bin...
Hi,
Just want to ask what will be the effect if I will use an external oscillator (32.768kHz) with a CL nearly at max specification, let's say 12pF.
Thanks.
Hi,
Can we send a message from a Provisioner to a Unicast address in a mesh network?
I'm using nrf52832 and can send orreceive message between nodes in the mesh but I...
Using 4-bit SPI mode on the Display Controller side: SCL,MOSI,MISO ... and DCX (by which the controller distinguishes between command bytes and data bytes). There's no obvious...
