Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Got called back to an old product that used nRF24LE1. Need to do a simple hot fix.
But I don't have the nRF6700 Dev Kit with me anymore. It cost almost $600 to get one from...
To the kind attention of Nordic support team,
I know that gazell secured libraries are available at least for keil compiler and nRF52840 device.
Are those libraries available...
Hi,
We are seeing a voltage of approx 1 volt on our USB connector when USB is not being used (VBUS).
We are using our device in a Wet environment; this voltage between...
Hello,
I am using nrf52840DK and I try to send data from sensor to ble toolbox. I want it to advertise for 1 minute and then go sleep for 5 minutes and do it again and again...
Hello dear Nordic Semiconductor. I use one of your creation - nRF52840 USB dongle. I have troubles with using USB CDC ACM. I add ble stack to gather info about advertisement...
Hello,
I want to do fast advertising (100ms) (LE privacy enabled) for about a minute, then I want to transition to slow (1000ms) advertising forever (or until a connection...
To the kind attention of Nordic support team,
I'm porting old code in order to use nRF52840 and s140 softdevice. During initialization of device information service I have...
i've been trying to update certification on the device (fallowed the guide https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/nrf-cloud...
Hi there!
Working with the nRF52840 DK, I am wondering how I might modify an existing SDK example in order to display the Tx and Rx Power characteristic on a hardware connected...
Dear I would like to put the license key to nff5-SDK examples into sdk_config.h file Format on thisiannt side looks like this 0xXX, 0xXX, 0xXX, 0xXX, 0xXX, 0xXX, 0xXX, 0xXX...
Hi I tried modifying the ble_app_uart_pca10056_s140 example as follows (nus_data_handler method modified only) such that it echoes the data back sent from the phone:
I...
Hello to everyone,
I was told to develop a simple BLE scanner using NRF52 DK (NRF52832). The idea is just to identify surrounding devices but we don't want to initiate connection...
Hello,
I just managed to trigger a syntax error for a seemingly normal set of compiler flags / defines in ser_dbg_sd_str.c:
Compiling file: ser_dbg_sd_str.c ../.....
I have to implement a custom I2C Bus communication. My Slave has to listen on all Addresses (eg. the Address 0x00 will be used as a Broadcast Address) and has to answer to...
I decided to move to 16 SDK, but I have problems with TWI. Whenever I try to read data from sensor, I get only 0 as the output. I use sensors ICM-20600.
When I try to read...
