I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi, I don't understand enough about electrical, but i found that a little piece of component in my nRF52840 dongle was gone.
It was something in this position:
It was...
Hello,
I'm trying to measure execution time of a piece of code in nRF52832. I was searching and found that I need to get the start time and finish time by using
beginval...
Hi,
I am using nrf52840 Preview - DK, with SDK v15.3.0 and Softdevice API 6.1.1
As we need to set NRF_LOG by setting the NRF_LOG_ENABLE and NRF_LOG_BACKEND_URAT_ENABLE...
Hi,
currently, i'm developing nRF52832 chip and I trying to use two GATT services.
I want to know about that "Can I use my custom services with Nordic Uart Service"...
I am basically wondering what the difference between these two examples in the SDK are?
Also, I see in both cases after the spi_transfer is called there is the following...
Hi Support team,
When I installed the nrf Connect SDK v1.2.0 with the Toolchain manager, I found that the files in the directory indicated were incomplete.
As shown in...
Hi. I am working on adding DFU to our application. I want to use buttonless dfu service for entering bootloader. I think the only thing one need to do is write a correct widely...
Hi,
I have a setup where one nRF52 based device is a master and generating a time pulse with a counter. On another side, I am having Android device with QCA6174A module...
hello team,
I'm using nRF CONNECT 3.3.0, SEGGER Embedded studio IDE with Cmake version 3.16.5 and SDK
my device (nRF9160DK) is connected with system but SEGGER Embedded...
Hi, I've successfully passed nRF Connect SDK installation by using GSA application (macOS 10.15.3, python 3.7.7, west 0.6.3). Now I'm in the SES 4.52c and have a problem in...
It looks to me that in NCS/Zephyr it is only possible to configure the system clock to operate off of the LFCLK. I haven't been able to find any Kconfig options that would...
We have 2 identical development boards and have been using only one until now. I was able to download code into the 2nd board successfully but it will not run. It does not...
Hi,
what is the valid range of interval for NRF_SO_GNSS_FIX_INTERVAL? when we set it to 5 it will failed, but 1 and 10 can be successful.
here is the code and error log...
I have a nrf24 transmitter and receiver that I want to set up for max speed. I have my SPI's both at max and I set the crf24 register to reflect 18db (was not sure how this...
