I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
We are using a flash part that is 64 MB in size. It is S25FS512. We are trying to use 32 bit addressing mode by setting sdk config flags. However this does not seem to work...
Hi,
Greetings!
I just tried Low Power Node example application from SDK for mesh 16.0.0
It works functionally well, however I am little curious to know below point(s...
Hi,
I start developing with a new MacBook Pro (2019) which only offers USB-C ports. Currently I am facing the issue that the Programmer App does show the connected Thingy...
Hi!
I have recently setup the development environment for my Thingy 91 on Windows 10 environment using nRF Connect Getting Started Assistant. But I am having some trouble...
Hi, I am working on nRF Thingy52 for a week. I am having SES with SDK_16.
I am having 3 nRF thingy to do a testing purpose
First i need to analysis how the thingy works...
I'm testing using the internal RC circuit to drive ble via the S132 softdevice. Set up is with Nrf52DK and Power Profiler kit. I got everything running and was measuring about...
Hi, How can I configure the LwM2M server (URL, Port, Credentials) on my Thingy91? Can I do this via MQTT and the nrf Cloud or do I need some specific tools?
I have a GT832C.01 (Bluetooth 4.0 BLE sensor detection module BMX055 9DOF NRF52832), I don't know how to program it, I can see it from the phone, but what software do I need...
I have a BLE board with a nRF52832 and some peripherals. It came with a preinstalled bootloader and firmware (the bootloader supports DFU via BLE to upgrade the bootloader...
Hi,
I am completely new to this technology,I need to interface BME 680[humidity,pressure,gas,temp sensor] with Nordic nRF52840 - how it is possible,i want know the hardware...
Hi,
I am using nRF52832 DK, with Segger Embedded Studio as IDE. I am using ble_app_uart example. I have used an encryption algorithm. The encryption algorithm is called...
Hi,
Does the SPIS generate interrupt for every byte of data receive ?
What kind of interrupt of event that SPIS will generate for data received ?
Please advise
Hi,
I need to assign Rising edge and Falling edge event in a single pin.
I try to assign both Rising Edge and Falling Edge event into APP_EVENT_PIN.
There is a error...
Dear all,
I have noticed that NRF_LOG_FLUSH() function is used in many examples after each nrf_log print function. In some cases though, the program freezes when I try my...
