Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi there,
I'm using nRF52840 dev kit board and v15.2 SDK.
I've set up a PWM using the PWM driver and is working well.
I'm frequently stopping and starting the PWM...
Hello everyone,
I have a nrf52832 (SDK v15.2.0) that is connected to a tablet via BLE. However, if I have several SPI transfers one after another, the BLE suddenly disconnects...
I am trying to retain the data on the board when it is transferred from my computer to the board through uart and once it is on the board through bluetooth to phone. Text...
I am now facing the following issues: https://devzone.nordicsemi.com/f/nordic-q-a/55975/about-reset-during-advertising
I call "sd_app_evt_wait" and go to sleep. Even when...
Hello Nordic Team,
I am creating application to connect with specific device using Name filter,
control is going to nrf_ble_scan_connect_with_target , where "sd_ble_gap_connect...
HI,
The code number for this softdevice version is 0x98. You can find the softdevice code number by typing nrfutil pkg generate --help
But the command only list upto...
Good morning; I am from Argentina, working in a Big Data Project using NoSQL and SQL tools. In fact, I deployed a architecture using Elasticsearch mixing ML, prediction, KPI...
Hello,
about two years ago we have made a Device basked on SDK 13 with S132 4.0.2 on it.
Now we had to build a newer version for our application and for this we have taken...
Hey.
I have a code for processor nrf51422 which compiles using a makefile. However, I decided to import it into a segger - with which I have no experience. For this I used...
Hi ,
I am just unable to find the FW ID for SD v7.0.1 anywhere.
I am using SDK 16.0.0 and SD 7.0.1 and would like to create a DFU package. Any of you know what is the...
Hi there,
I am trying to transmit data with high MTUs via pc-ble-driver-py. The data is sent from an nrf52840 with own firmware.
After the bug in nrfutil was fixed,...
Hi,
im trying to turn on LEDs on my custom nRF52 board. Im using LEDs on 13,14,15 pins. I config pins in pca10040.h to my LED pins, but they dont work. Also if i try to...
I am trying to set up multiple ble diagnostic type services for different sensor devices, from a single nrf52840. The services share a common base id and some have the same...
hi! I'm trying to use the following to configure the GPIOs in nRF52DK for the LED blinky.
nrf_gpio_cfg_output(pin_number)
But I'm not sure what number should I use for...
