I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
I've used the 'Getting Started with nRF9160 DK' tutorial to setup a development environment, I have a problems with loading asset_tracker project. My output:
Loading...
I understand there is a hard fault happening in the SDK. I am using SDK 15.3.0, I am not on a sdk example, but on a specific program I am doing I can't share. It happens a...
Hi,
I added a small shunt resistance to see current consumption of nRF52832.
I see current ripples when DCDC regulator is enabled, this ripples doesn't exist when DCDC...
1. We are running our nrf52832 based project on Eclipse and are able to compile, build and run the project on our target hardware. So far, so good.
2. Now, in addition we...
I'm working with the light switch server example and nRFMeshProvision example project for iOS.
How do you send arbitrary data to a board? I understand the provisioning process...
Hi,
I noticed that there are a few methods in nRF52 SDK v16 to blink LEDs:
Use bsp indication methods which seems based on app_timer;
Use led_softblink library which...
nrf52832, SDK 15.3
The average current consumption is 9.53uA in my system with SPIM. After I init another SPIS, the current consumption goes up to 478uA. CS pin keeps high...
Now I am using nrf9160DK for development. In my project, I need to use a random number generator and a highly accurate system time stamp. Is there an API that I can call directly...
Hello,
On nordic nRF9160dk I want to send SMS and receive the data from UART simultaneously. UART needs 3V VDD supply and for Sim card it is 1.8V. So how this condition...
Does SoftDevice S112 or S113 offer mesh support on a nRF52811?
The intended use is for an end-device running very simple app-logic. According to the SoftDevice properties...
Hi there,
I'm using nRF52840 dev kit board and v15.2 SDK.
I've set up a PWM using the PWM driver and is working well.
I'm frequently stopping and starting the PWM...
Hello everyone,
I have a nrf52832 (SDK v15.2.0) that is connected to a tablet via BLE. However, if I have several SPI transfers one after another, the BLE suddenly disconnects...
I am trying to retain the data on the board when it is transferred from my computer to the board through uart and once it is on the board through bluetooth to phone. Text...
I am now facing the following issues: https://devzone.nordicsemi.com/f/nordic-q-a/55975/about-reset-during-advertising
I call "sd_app_evt_wait" and go to sleep. Even when...
Hello Nordic Team,
I am creating application to connect with specific device using Name filter,
control is going to nrf_ble_scan_connect_with_target , where "sd_ble_gap_connect...
