I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
I am using a BMD 349 module based on nRF52840.
I am interfacing with AT25SF041 flash memory.
I am using SDK 14.2.
I am writing a byte to a specific address in Flash...
I recently purchased a Thingy:91. Initially it would not connect to the local network. I purchased a a J-Link programmer and via the nRF Connect Programmer updated the modem...
Is it possible to Read the battery status and/or the temperature value from the nRF52810, write that data to on chip memory, and run a code to modify the Major and Minor values...
To the kind attention of Nordic support team,
after some months I gave a look to the segger toolchain configuration for the device host example using the secured gazell...
Hi
I am trying to set up my visual studio to communicate with my nordic device and found that PC-ble-drive can help me with this.
I followed the steps mentioned in the...
HI I'm currently working on measuring distance between two points with two nrf52840 modules with the example "nRF52-ble-long-range-demo" (you can easily find it in github...
I have configured "nrf 52 DK" to worked as BLE sniffer. I am trying to sniff the data packets exchanged between two TI CC 2650 devices (in which one is master and other is...
I am trying to configure my nrf 52 DK board as BLE sniffer. I am following this blog " https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nc_programmer%2FUG%2Fnrf_connect_programmer...
Hi,
I'm using the Light Switch example and would like to read out the own address on a light switch. Is there any application call, such that the stack returns my own...
Hi,
Currently I’m working on a device which is, on the one side connected to a smartphone via BLE and on the other side to another uC via UART.
Therefore, the UART speed...
Hello,
I did a code base on aws_fota sample and added a watchdog, a timer (to feed watchdog) and modified some outputs. Tests about thèses items looks correct.
When my...
Hi,
The Zephyr LwM2M client seems to leak pending objects that are used to track retransmissions. When this happens it enters a loop where the lwm2m_rd_client stops sending...
We noticed strange behavior when measuring voltages with the SAADC with our custom board. When VDD_GPIO is at 1.8V (which is our target), the ADC measurement error is about...
Hi, We've been having problems trying to implement a high-speed uart communication between the nRF52832 and an STM32. We switched to using libuarte so we can use DMA even...
I'm running the Nordic/Thread SDK 3.2 with an NRF52840 (Rigado BMD-340) on SES 4.42.
I've got a project using BLE + Thread and I'm having problems implementing a hardware...
