I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I'm trying to finish a handmade custom board I started. I had previous problems with the crystals, and a few others, but right the thing seems to be working ok. At least I...
NRF52832 on SDK 16.0.0, softdevice s132 (using SES) When writing constant value with FDS it saves normally, but when I try to write variable it saves some garbage. Here is...
Hi,
Is it possible to give 3.3V to the Vdd pin of my nrf52840 to change the reference voltage of saadc to 3.3V ? Do I have to change any configurations for the same?
Hello community
I want to advertise when physical pin 0.24 is high, and stop advertising when pin 0.24 is low. For this, I based my code on the Beacon Transmitter Sample...
Usually, I programmed the Thingy 91 with the nRF connect Programmer (right now version v.3.3.3). As my Thingy did not work with the asset tracker software and only with the...
Hi,
I am trying to integrate an UARTE application code with OpenThread example(thread_mqtt_sn_client_publisher_pca10056) on my nRF52840. My application code uses UARTE0...
Dear Sir/Madam,
I need help. I am using UART to send the data in the mesh topology .and I configured mesh using light_switch source code. is it enough to send data using...
I am trying to interpret the values in the INFO.VARIANT register for the nRF52840. The datasheet states "Build code (hardware version and production configuration). Encoded...
Hi,
After following the steps for building the documentation, I always get the following error:
"CMake Error at CMakeLists.txt:92 (add_subdirectory): add_subdirectory...
Dear All, I am trying to develop a simple BLE scanner that will scan for BLE beacons and print the retrieved packages. I am using nRF5 SDK v16.0.0. I have mostly succeeded...
I'm using an SES with NRF52840, w/ SDK 15.3, and SoftDevice S140. Im working on DFU and have two components:
- a main app that already takes care of moving a FW image into...
Hi
We are using %XMONITOR to get the network status and parameters, but we cannot understand some of its response:
1), sometimes, the PLMN may be "FFFFFF" and TAC may...
Hi!
I am in the process of trying to figure out how much it is actually going to cost for our devices to support LTE-M, and I have realized that I don't actually know what...
I am trying to write a simple application to publish messages over MQTT to an AWS IoT-Core broker. I started with the MQTT_Simple and AWS_FOTA examples. When trying to do...
before the question , I hope you understand my poor English.
i make a project using nrf52840 dongle
when event of an interrupt signal occur , the chip must wake up...
