Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
I built a device using the nRF52832 SOC, have programmed it with the Version 16 SDK>ble_app_uart_pca10040_132 using Segger Embedded Studio. I am able to connect to the nRF52...
Hi,
We are developing a product using NRF52832 chipset with a small 128*160 LCD (based on st7735s controller using 8 bit parallel interface).
I noticed that there is st7735s...
Are there any limitations that will not allow me to make the ble_app_hids_keyboard example with FreeRTOS?
If no, is there any examples that will help me easier to migrate...
Hi,
I see that Eddystone packets has service data limited to 20 bytes frame data. But unfortunately I have to encode more than 20 bytes.
So can I use advertise mode as...
Hello everyone.
I have made the next solution for merging softdevice into debug fw.
i 've added the next lines in ld script
MEMORY { SD_FLASH (rx) : ORIGIN = 0x00000000...
Hi,
I want to output a high & low voltage with an array, the array contains a sequence number, looks like: {0, 1, 0, 0, 0, 1, 1, 1, 1, 0, ...} , and the length of the...
I'm wanting to create and Android application that can communicate with a nrf24l01 module. Is there an android library available that will permit this? Thanks in advance!
Hello Everyone,
Consider i have 2 MCU's on board connected via UART interface, one is any ( Target ) MCU (MSP32, STM32, etc) and the other is Nordic's nRF52832 ( Host )...
Hi,
We have two nRF9160DK and both have the SIM card issue as below, and our development was blocked by this issue, so please help check it, thanks!
original case
Hi!
I am trying to figure out the app_timer_library but am running into some (to me) strange behaviour. For the first seconds it appears as if the LFCLK is running much...
Hi,
I've built a application based off of the ble_app_hrs_rscs_relay_pca10040_s132 example in SES using a Laird BL652 module (nRF52832 underlying device). Presently the...
Hello
I successfully build asset tracking example , for nrf9160_pca10090ns
when I try to run using segger, I get the following:
SPM: NS image at 0xc000
SPM:...
Hi,
I am trying to use the Android-BLE-Library with my nRF52832 device (I do have another test Android app which can work w/o using the library).
I followed the Github...
I am porting RF evaluation code to the nRF53 NCS/zephyr/Segger Embedded Studio toolchain, using only the network core to start.
How do you recommend configuring the network...
