This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I am no programmer, but I wanted to try the Wake-on-NFC example on the 52840 dongle (I soldered an NFC flex on pins P0.09 and P0.10). I have downloaded SES and nRF SDK...
I want to connect heart rate sensor and bike power sensor together. I config channel 0 for heart rate sensor,and channel 1 for bike power sensor. Ant work well when both sensors...
I've just tried to compile and run the stock lpcomp example on two different computers, targetting an off-the-shelf 52840 dev board. It compiles, and starts fine, but doesn...
Hello,
I am creating an application that counts the number of times the button is pressed (Every high to low transition).
I am using GPIOTE to sense the high-to-low events...
Hello,
I am considering redistributing the SDK source code. I also saw the following, but hasn't it changed?
devzone.nordicsemi.com/.../32969
【SDK：15.3】
Hi,
How can I understand what all Errata's are applicable to softdevice and are taken care of?
For my application I am aware of the modules/peripherals being used and...
Hi,
I noticed there is no SWO support mentioned in Product Specification 1.1 for nRF9160. But since the architecture seems similar to the nRF52/nRF53 that have SWO under...
I have been interfacing with the Macronix external flash via the nfrx_qspi library for logging. While I am able to use nrfx_qspi_read() to obtain my log data, I am also able...
PM_MCUBOOT_STORAGE_ADDRESS and PM_MCUBOOT_STORAGE_ID seem to be no longer defined as of SDK1.2. As per the discussion here , I tried using DT_FLASH_AREA_STORAGE_OFFSET which...
Using nRF52811, Segger SES, and SDK 16.0, I have some times that seem to be off by ~2X.
I'm timing by setting a gpio before and after the event and capturing with a scope...
Hi
Referring to
https://devzone.nordicsemi.com/f/nordic-q-a/58652/additional-questions-to-nrf52832-errata-220-clearification/238659#238659
From the above post, the...
I am new to the nRF9160dk board. I have been able to compile and run some of the sample programs. I am now looking to have a simple program to talk to external uarts 0 and...
I need my sara sara-r410m-02b ublox module to connect to the cellular network using at commands. For this reason I require to send the commands by means of programming lines...
Hi
I have a custom who is using 52832 to develop a Bluetooth door lock, including a NB-iot module, The door lock is unlocked via app Bluetooth.
the question is : There...
