When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi,
I'm having an issue with timers. They work fine for shorter timeout values (<8hours) but after trying with a timeout value of 24 hours, my timers expired immediately...
Trying to implement the BLE peripheral advertising code, but sd_ble_gap_adv_set_configure() in ble_advertising_init() returns error NRF_ERROR_INVALID_LENGTH. Any help will...
Dear experts,
My app needs to monitor an incoming DRDY signal changes at 200Hz to 16000Hz. I am considering to use NRFX_GPIOTE driver to detect the DRDY event. It seems...
Hi Nordic,
I was checking the ble_app_uart_coexist example application and it says it is a combination of both UART & Mesh. So would this support provisioning via mobile...
Hi, team. ********** environment : SDK : Mesh v3.2 (w/ SDK v15.3.0) SoC : nRF52840 IDE : SES ********** I am challenging to handle each event, such as Mesh receive interrupt...
Hi all,
Radio notification inactive state interrupt is coming but I was not able to do any action by comparing it.
I am thinking, if radio_evt is false then it is radio...
Hi,
I need trigger repeated SPIM via PPI for a batch of samples until the given RAM buffer is full. Then I need start another round of batch SPIM with another buffer.
...
Hi,
I am trying nrf52832 with pca10040 board. My app uses s112 soft device and also SPIM0 to collect data from a slave device. No event handler has been used when initializing...
I want to know how to control BLE connection of nRF52832. I am using softdevice S132. I have a device that works centrally and a device that runs peripherals. When the peripheral...
nrf52832.
SDK14.2
Segger ES V3.34a
Options for Sequential Serial numbers
We have managed to program a single serial number into the UICR, using our Development...
I am trying to interface I2C EEPROM (AT24C512) with nrf52840 and I am directly writing to and reading from the registers mentioned in the datasheet. I am seeing the i2c waveforms...
Hello -
We are also bumping into the problem described here , where it is not possible to initialize LESC when BLE is initialized from a FreeRTOS task. The nrf_stack_info_overflowed...
nRF52DK
external board with 51822 and mems
I connect my external board with nRF52DK as this (left is board, right is nRF52DK):
SWCLK -> SWDCLK
SWDIO -> SWDIO
VCC...
Hi,
I got some troubles on the communication distance between the two units which one acts as central and one acts as peripheral, I tried to adjust the BLE parameters the...
