hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
While going though the Makefile of the FreeRTOS HRS example in SDK 16.0.0, I noticed this part:
By default, link time optimization (LTO) is not enabled.
If I enable...
After Christmas update we are unable to use DFU from Android devices.
We've been using such function on a regular basis with our devices and everything has always been fine...
Hello everyone,
I'm using a NRF51822 as a central device, I connect to a peripheral (NRF51822-based device), then I stop the scan. At a later time I initiate another scan...
Hi,
I am trying to program nRF52832 custom circuit with nRF52 DK, I have connected debug out from the nRF52 DK to the custom circuit containing nRF52832 debug in. When I...
Hey Guys,
i am currently experimenting with the NFC functionality and have an issue with our "nrf52840-DK" boards:
i am testing with IAR (8.40.2 - including the library...
Hi there,
I'm trying to use serial library from SDK to interact with cellular modem (AT commands, not nRF9160). I've read documentation (library description, api). May be...
I have build and flashed the zephire/sample/bluetooth/hci_uart on nrf52840 board and connected the board with ubuntu but hci interface was not created when checked using hciconfig...
Hi,
We have chose LCD which has only 3-Wire support CS, CLK and DI so we have connected that pins with nRF51822 chipset. Now Please see the below image which shows that...
Hi All,
I want to read/write long characteristic (200 bytes max) from Android to my device.
I'm working on the 15.2.0 SDK and S140 Softdevice.
I read some Q&A on...
Hi there,
Right now I am doing some dry research into long range Coded PHY for S=8 or S=2 since I need to have some extra room in the link budget to go the distance. The...
Hi, I'm trying to adapt the ble_gateway example for nRF91dk to use a nRF52 instead a Thingy52. When I change the UUID at ble.c from Thingy to nRF52, I'm not able to get a...
Hello guys,
In next few months I've to put down a new design for a medical product. Both nRF52840 and nRF5340 would fit well the application requirements. But I think this...
I want to use two UARTS ie uart0 and uart1. I read that nrf51822 gpio pins can be set as rx & tx but i couldnt find any example.
I am using SDK12.3
Please attach some...
Hi,
I've looked around the DevZone for answers to this, and haven't quite seen an answer, so I'm going to post my solutions here.
I am using the secure bootloader from...
