Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
51822, S130, SDK11.0. In order to save current, I disabled fast adv and set the slow adv interval to 10seconds. The current is low now, but I am facing connecting issues with...
with regards to nrfconnect ios v2.2, has anything changed with respect to service changed characteristic or service and characteristic discovery?
(behaviors described seen...
Hi nRF team,
I am configuring my GPIO pin with below code sample.
out_config = GPIOTE_CONFIG_OUT_SIMPLE(false);
err_code = nrfx_gpiote_out_init(MEM_SPI_SS_PIN, &out_config...
in ¨¨Blinky example¨¨ we press button on one board and led get ON on other board.
I want to ask how can I modify this example or any other example
what are the functions...
Hi
I am looking for BME680 example code for Thingy91,since I donot have access to NB-IoT / LTE network as of now, i can't use the asset tracking demo code. I just need BME680...
hello
we used sdk_15.2.0 ->proprietary_rf -> esb_ptx example to check 52840 transmission.
now we have 61440 bytes need to be sent out. i used following code；
int main...
I`m searching after a document / description how to setup a user test case for BLE RF distance range measurements. Maybe Nordic have a smart phone app which we can use to...
I am evaluating NRF for a commercial project. I am also new to this BLE business so trying to learn fast.
I am trying to run the supplied BLE UART example on the NRF52DK...
I am trying to develop a low power scanner with nrf52832 which is is acting as both central and peripheral (beacon)
I need to detect other tags like itself transmitting...
Hi,
is there any example of firmware that can be used on nRF24LU1P that perform some data receiving on RF side and send them over USB?
The most important part is the USB...
Hello, We have designed a PLE peripheral based on nRF52840, SDK16.0, Softdevice v7.0.1. We have having an issue where, occasionally, we send a certain data (a command) to...
Hi everyone,
I created a custom service that I want to be advertised through scan response. Also, I want to advertise the INFORMATION SERVICE through advertising data. I...
Hi, I'm working with nRF52840 with NFC. I don't have yet the external antenna to connect to (now I'm using uFL), but I'm not sure about the trace width that goes from the...
MeshSDK: 3.2.0
StockSDK: 15.2
Hello,
I have a network where the sequence numbers have become corrupt due to removing devices from a network and then provisioning other...
Hello,
I've been trying to write my own library that uses UART.
I went through the "uart" example and wrote this piece of code.
uart.c
gpio.c
main.c
...
