Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Dear All,
We work on the NRF52 CSP revB. We have a board with two external crystals (32MhZ and 32kHz).
When we use the example program with BLE and UART, it works great...
Hi,
How can i get time stamp from RTC1 timer? While i am using app_timer + Softdevice?
Or any other way
Thanks and Regards,just to get timestamps from timer?
Faizan...
Hi,
I added DFU function to the example of ble_app_hids_keyboard according to ble_app_hrs_dfu.uvproj.
Test environment: nrf51822_xxAA, SDK_v6_1_0 and S110_v7_1, before...
Hi all,
I would like to use Pstorage module. Since flash endurance is 20.000 write/erase cycle, I need to use it very efficiently. If I use pstorage_update function it...
Hello,
I am quite new to Beacon development. I am trying to use the examples of NRF SDK 10.0 on the NRF Beacon. I would like to "install" the application via OTA. I tried...
Hello,
DFU tool (android) is cool but if you have a lot of devices to update it's long. Is there any batch tool that can update all devices that fit (MAC list or SSID filter...
When executing the Bond command on the 8001 and trying to pair it from my laptop (Windows 10) or iPhone (iOS 9), I receive a strange order of events to the command:
...
I'm trying to replicate an Arduino Uno application where we connect a M3Q alcohol sensor into an analog pin and feed the data into the ADC. The specific board I have is made...
Hello,
sd_softdevice_enable falls in hardfault. I have no 32.768 KHz crystal but is set lfclk with NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM.
I'm running my application on a...
HI,ALL,
i want to try to developer with bluetooth develop studio,which developered by BlueSIG.
i now download the BDS and the PLUGIN for the nordic NRF51.
is there...
Hello,
Does the S120 have support to know on which advertising channel it received an advertisment? Or some kind of feedback to know on which channel the S120 device is...
Hi,
Does anyone know the event end point addresses for the following on the nrf52832:
RADIO_EVENTS->ADDRESS
RADIO_EVENTS->READY
RADIO_EVENTS->END
The addresses for...
