Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hello Everyone,
i am trying to simulate the circuit using Proteus so can anyone tell me where can i find the Pspice model files for the Nrf51EVB is it available? any suggestions...
Hello to everyone.
I write code for NRF24LE1 using KEIL and rtx tiny. But i have some problems.
When i power on my device, programm don't run correctly, but when hard...
Hi experts,
The softdevice is s120. I get error code BLE_ERROR_NO_TX_BUFFERS after calling sd_ble_gattc_write() several times. I want to ask what does the tx buffer mean...
I have a strange problem on my target nRF51822. When I try and use the UART interface between my nRF51 and my host MCU, it causes the nRF51 to reset and the RTT terminal to...
Hi,
I've been playing with NFC on nRF52. It sends "Security Manager TK Value" over NFC. There is currently no option to use LE SC over NFC in examples, which is to send...
Hello
I have an problem using I2C on my custom board which uses an Nrf51422 SOC.
I have an RTC chip connected to it and I have no idea how to use your libraries.
The...
Hi! I'm using Arduino BLE micro and good results so far. With some accellerometers connected via I2C.
Today I have a strage behaviour.
I connect the arduino, ok, open...
Hello everyone,
I have a nRF51822 dev board connected through USB to my PC.
I have connected it to COM5 using Terminal and now I would like to interrogate BLE like we...
Hi guys
I have a custom board with NRF51422QFAA, load "s310_nrf51422_2.0.1_softdevice", program on "nRF51_SDK_7.2.0"
the bootloader I used is "dual_bank_ble_s310"
...
Is there a way to control the max # of packets be transmitted in one connection interval?
(We want to vary it from 1 - 6, knowing that nordic can support up to 6-7.)
Has anyone had any success setting the configuration register on TMP102/112 temperature sensors via I2C? I'd like to switch the sensor to one-shot mode to further minimise...
Hi everyone !
I'm trying to send data from an nrf51822 to an nrf24l01 with arduino and I guess I'm doing something wrong...
For the moment I succeeded to have these talking...
I have a simple ANT beacon application.
UART will be enabled to do some communication. How can I turn it off before ANT goes into sleep mode? Is there a call back function...
I want to send a set of 64 bytes data with ble. as I understand, the max data length I can send within a characteristic is 29 byes. when I send 4 bytes data it works fine...
