Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hello, I am new to Nordic NRF51dk and I'm working on the SPICommunication_module c.
For the switch case statement, I am trying to understand what the spi_master_evt.evt_type...
Now, I'm using "nRF51\peripheral\temperature" example to test something for my nRF51 DK board.
I have upgraded sofeDevice s110 v8.0.0 in DK and I can use Keil "Download"...
I am using Unity3D BLE Plugin by Shatalmac ( www.assetstore.unity3d.com/.../ . Upon using the example code, it is discovering the UARt custom service, but dont know why it...
I am really struggling getting anything to work on my revision 1 module and as it has nothing connected at this moment all I can use is BLE or UART to observe any function...
Hi,
I would like to change the the advertising interval of the beacon kit in the sample ble_app_beacon app; however, I could not figure out where this parameter is. I see...
Hi,
I want to connect a rotary encoder.
So I have 2 pins of the nrf51822 connected to the encoder and I have to check which one change first to increase or decrease the...
So there seems to be a conflict between the TWI and the Softdevice. My I2C communication works over TWI fine in isolation but when i try to send data over ble the TWI doesnt...
I am using the nRF24le1 in Enhanced Shockburst mode.
The datasheet describes how it is possible to upload acknowledge packets, W_ACK_PAYLOAD, to the TX FIFO. And then the...
Hello,
I need to get RSSI with the NRF51422 (pca10031, S110), but i don't want to connect with a central device (i.e. Smart Phone). The central device should scan for bluetooth...
We tried to pair with and connect to nRF51822 DK running HTM app with SONY VAIO fit15e NB and always fail as we did the following steps.
We also tried some devices like ASUS...
Hi,
I just replaced the BLE chip in my board from CC2540 to nRF51822. I simply want to know how to configure the interrupt on a pin as well as rising/falling edge interrupts...
