I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
HI :
I am trying to use spi to communicate with a slave device . The slave device only have 3 interfece SDIO SCk NCS. I need to read the register of the slave . According...
I programmed a nRF51 dongle as an ESB receiver using the esb_ptx_prx example code. It sleeps most of the time by calling __WFI() in the while loop.
I used an external 3...
I have a oneshot app_timer that I'm using as a software watchdog timer. Under normal operation is never supposed to go off. I'm loading the timer with a 15 second timeout...
Hiii,
I am working on the ble_central_and_peripheral program(s130) in sdk8.1.0 .I could connect the device to the MCP and on clicking enable service we gets the notification...
Greetings,
I find it much an arduous task trying to sift through all the SDKs and Documentations in order to find the one specific material that I need. I've installed...
when I use softDevice S110, there exists ble_evt_dispatch function, Can I define event ? if I can, how to define event and how to use event handler . Thank you !
Hi
I want to update the connection parameter and send this request from nrf51822 to a smartphone app. I see there is a function ble_conn_params_change_conn_params() for...
I'm sure there is something obvious that I am missing, but bear with me. The following link references a function called: nrf_drv_gpiote_out_config :
infocenter.nordicsemi...
I'm trying the example in the SDK v0.9.1: examples\spi_master
When I load the project, build it, and debug it, all that happens is that it goes into a failed state where...
I occasionally get an NRF_ERROR_NO_MEM error when trying to add a custom characteristic. I'm only using 3860 bytes of ZI data, stack = 2048, heap = 2048 so it seems like I...
Hi
I am working on the ble_central_and_peripheral example in nRF51_SDK_8.1.0_b6ed55f .In this example it is possible for us to connect to 3 peripherals only.But we would...
Hi, are there any examples in C for how to directly access the registers on the chip? I realize this is a super basic question, but all the register access in the examples...
Hi,guys
I set BLE parameters like this:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL MSEC_TO_UNITS(1000, UNIT_1_25_MS)
#define...
Hi,
I'm using sd_ble_gap_connect to connect to a set of known address and whitelisted devices. My central periodically (once an hour) needs to check on a known set of devices...
