The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi everyone :
I have some questions about nrf51822 ble S110 ,I have two ble device ,both device used S110,is it possible use the first device to scan the second device to...
Hi,
I used the pstorage example mentioned here and got it to work to an extent.
A snippet of my code is :
retval = pstorage_init();
if(retval != NRF_SUCCESS)
{
...
Hi,
I created an Android project that scans nordic beacons and parses the data in it (such as the tx level, major. minor, UUID etc). I'm doing some low level parsing to...
I used version 3 nrf51822 along with s110 v8.0 header files for radio unblocking. when i was trying to compile there are many errors shown up because some of the soft device...
I am driving a piezo at a fixed frequency but want to provide adjustable volume by adjusting the duty cycle. I would like to adjust it by setting the duty cycle to 5 levels...
Instead of central-peripheral relation based cluster, I am planning a linear daisy chain like network model with BLE, where a series of BLE nodes will just relay the information...
I have a system fully operational using the nRF8001 communicating to both IOS and Android devices using nRFUart app from Nordic as well as a custom app using the uart tx and...
Using IAR CWARM to develop on CFAC. IAR currently doesn't have CFAC device support built in. So I am copying over CEAA config files and manually updating. I realized that...
Hi Team,
Can anyone help regarding Cable Replacement service.
Is this service is already supported in softdevices?
What are the options if not supported?
Hello! I trying to use peripheral example with s130 stack. I have some problem:
Device is advertises well. If i connect to the device via mobile application nrf Master, after...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I need to poll a NMEA data stream and it's easiest getting a byte at a time, but it's dropping to 30ms between individual reads in this loop:
uint8_t next = 0;
uint8_t...
Hi.
I'm working with the nRF51422 devlopement kit (pca10028) and I need to mesure the highest throughput between the nRF51 DK and a smartphone. I have seen several post...
