Dear Nordic Engineers
The following documents are our hardware designs. When we conducted the test, we found that we couldn't obtain the GPS satellite signal and the 4G...
I’m using the Zephyr nordic,npm1300-charger driver on an nRF52840 to control the nPM1300 PMIC charger. At runtime I need to be able to turn charging on and off—on command...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi,
The nRF Toolbox app on iOS crashes when opening user added files in the DFU. These files are added to the app via iTunes. The version of the nRF Toolbox is 1.7 which...
Hi,
We're producing a custom board based on the nrf51822 and would like to add a USB Serial chip.
The current contenders are:
a) FTDI 232R
b) ATmega8U2 ( www.arduino...
As the picture shows, I saw this softdevice_hex option available.
The error says, "require nRF_SoftDevice S310_Hex".
But where to this missing component.
My development...
Im sending an 8 bit int using my AVR controller as follows:
static uint8_t* dummy_heart_rate = 6;
aci_loop();
if (lib_aci_is_pipe_available(&aci_state, PIPE_UART_OVER_BTLE_UART_TX_TX...
Are there any pins that I can NOT use for SPI on the nRF51822? I'm not seeing any notes in the latest documentation but would like to make extra sure before I spin a board...
Hi there,
Using mbed i have currently programmed an nRF51 DK to transmit data through a custom service with 6 read only characteristics. Is there a simple way i can alter...
Hello.
I cannot get my head around app_timers. After reading the docs, examples and answers on the devzone I'm still unable to get it running. The timeout callback isn...
I am trying to add SPI to the ble_uart_example on my nRF51-DK but when I try to debug my code debugging just stops (All "step one line" etc. buttons grayed out) at this line...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I'm using nRF51 Development Kit to program the beacons. I've connected the beacon just like it's described in the last update of this thread using the 10-pin adapter...
Hi,
I just noticed that the nrf51822 doesn't have an eeprom and I already had the pcbs done. Can I use the NVMC to write USER data on the CODE (is it flash memory are?...
I am trying to do over-the-air (OTA) device firmware update (DFU) on a device with bootloader same to the "dfu_dual_bank_ble_s110" example in the latest nRF51 SDK . On the...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
We are using Gazell to stream data at <=6mS intervals for very low latency wireless gaming peripherals. We'd like to have many of these peripherals devices (more than 24)...
