why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
I'm using the following TI IC www.ti.com/.../tps62736 to get 3V from a LiPo battery. It has a VIN_OK pin that I can configure to alert of battery low level. The problem...
Hi,
I am trying to get even a basic ARM GCC example set up using the provided toolchain code, and am having a rough go at it.
First, what is the most recent, working...
In the s110_nrf51_8.0.0_migration-document.pdf, the ROM and RAM start and size for the v7.0.0 and v8.0.0 are specified as follows
s110_nrf51_8.0.0
IROM1 - Start...
What should the connection or other settings be to have a peripheral always connected? It is a bit contradictory for low energy device, however for a lost&found (link-loss...
Hi,
I just started on developing on the nrf51-DK. I started with blue_app_proximity, and I am trying to hack the immediate alert to do a toggle a led. I initialize the...
Hi,
I am trying to save/restore some configuration variables to/from the flash storage. If I do it using S110, it works perfectly fine and I can both store and read values...
Hi,
I have the same problems as described in devzone.nordicsemi.com/.../
I'll post details here as requested. I do the following:
-Connect P0.30 to ground (see photo...
We are working on a BLE home automation application. It is likely that some homes could have 10 or more of our devices. We also need to allow the homeowner control of which...
Hi Team,
I am trying to implement Blugiga's cable replacement service in Nordic chip.
I have successfully changed required UUIDs for services and characteristics please...
Hi all,
Can I update the value passed to the sd_ble_gap_adv_data_set() to do a scan response at any time?
For example when I get an interrupt from a button, can I update...
Hello,
according to the BLE 4.1 spec, a device can be able to be slave in multiple piconets at the same time. Will this ever work with the S130?
I do not know how the...
Hi, Nordic Enginner:
Now i want to use a external mcu to programe the nrf51822 by signal bank hci dfu mode(BLE DFU,we do not need! ). Also we have a pc softawre for control...
Hi everyone :
I have some questions about nrf51822 ble S110 ,I have two ble device ,both device used S110,is it possible use the first device to scan the second device to...
Hi,
I used the pstorage example mentioned here and got it to work to an extent.
A snippet of my code is :
retval = pstorage_init();
if(retval != NRF_SUCCESS)
{
...
