Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hello,
I'm looking to disable the Bluetooth in the ledButtonDemo,.
In the led_write_handler, I've replaced the code by :
if(led_state == 0)
{
sd_ble_gap_disconnect...
Hi
I tried to check nRF51 SDK on IAR Embedded Workbench for ARM 6.70.2.6310. But he said that the project is broken.
It looks like there are no setting files for all...
hi,
i'm working on change 'example project file using softdevice s110' to 'using s130'.
but, i don't know where exactly need to change.
just downloading softdevice s130...
I need to use the 8.0.0 version of S110 with my beacon which contains 7.1.
Since the Android DFU utility supports updating the Bootloader and softdevice with a zip distribution...
hi,guys
For testing the comunication between BLE+timeslot device and radio device, I change the code as below:
void start_timer(void)
{
NRF_TIMER0->TASKS_STOP = 1;...
Dear Nordic,
Whats wrong with the below code. It works well in RFduino but when I try to port the same code in Keil environment.Its not working throwing error as
1.identifier...
I just got a new target board back from fab/assembly and I'm trying to use the debug out connector on the PCA10028 to program the new target.
My target is the NRF51822...
Is there a beginners guide on how to get a console output working for the following setup?
keil v5 & SDK 6.1
nrf51-dk connected with the
TC2030-MCP-NL to a
nrf51822...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hello,
I am new to working with nrf52 and was looking for a way to make printf work in a blank project that I have created. I followed the uart example for the peripheral...
Hi
Now I'm using the pstorage module to save some data.But I meet some problem,I hope I can get your help,thanks a lot.
It seems that the block has been created successfully...
Hello everyone
i am trying to run the pwm library exmaple from github into the SDK VERSION 9.0 but it is showing lot of errors like
............\components\drivers_nrf...
Hello,
I am working on S110 SDK 9.0 and softdevice 8.0 on EK board. I am able to authenticate the connection using static passkey.
I need the information about encrypting...
A LOT of great information is presented by the engineers. Is it possible to post videos of the presentations?
Apple does this for the WWDC sessions. I find myself watching...
