I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hello,
I am working on nRF51822 S110 softdevice 8.0 and SDK9.0. I am creating paired and unpaired states and the system will goto unpaired only if it is unpaired from the...
I know nrf51 timer0 can be configured for 16,8,24 and 32 bit modes
and timer1 and timer2 can be configured for 16 and 8 bit modes.
But what can I expect the value to be...
I'm going to star a new product development using nRF51422 supplied by a 3V battery. Since it is a low cost product the idea is to use the nRF51422 internal DCDC to provide...
Hello,
I'm using an external chip that decodes my RF transmission and outputs the data on two pins DAT, and CLK (data and clock). Currently I'm reading the data with GPIOTE...
We have written our own softdevice, but now we have a question about the stack pointer.
I read in the softdevice specification that the nordic softdevices share the stack...
I have been trying to establish a link that will feed sensor data into my com port via a Bluetooth uart bridge. I got my closest today by doing the following.
Load SDK10...
I'm having trouble making a single bank dfu mode with 128k NRF51822 chip.
Here's the problem;
Works fine when everything(SoftDevice, Application, Bootloader) is all...
Hi,
I am a newbie to Nordic BLE.
A make error occurs when building the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0 on my cross compile environment...
Good morning, i have windows 7 and at this moment i have installed "Gnu tools for ARM embedded Processors", "GnuWin32 ‐ GNU Make utility", "GnuWin32 ‐ Core Utility", "nrfgostudio...
Hello,
on our custom hardware design, the hardware reset won`t be executed after programming with nrfjprog.exe, until complete new boot with disconnecting Vcc.
After reconnecting...
We are going to use nRFgo - Bluetooth direct test mode to evaluate the nRF51 device RF performance, and we need to load the DTM (Direct test mode) application to the device...
Hello
I have an nRF51822 serving as s supervisory micro for an embedded Linux board. Two GPIO pins from the main CPU are hooked up to the nRF51822 to implement SWD for...
Hello.
I'm using nRF51822, nRF51_SDK_8.1.0, and looking for same useful sample code for ble central with HoGP (HID over GATT Profile).
please let me know where is it...
Hello,
Is there someone to confirm than Keil MDK-Cortex-M edition is OK to develop app on nRF51 and nRF52 Nordic chips or do I use MDK-Standard?
www2.keil.com/.../
