Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
Hi,
Hope this is the right place to ask this. I've been trying to reset my password on the nordicsemi.com website but it doesn't seem to work. I receive a mail with my username...
Hi,
I am using nRF52 + Eclipse (gcc) with the ble_app_uart application.
I have an iPhone 6+ with nRF UART app running.
If I send <= 59 characters through the virtual...
Hi, is there an example that show how use the pwm with ble?
i'm new on keil.
i have used mbed until yesterday, the pwm that use keil is a hardware os software pwm?
thaks...
Hello Nordic,
I am following example code [--ble-app-lbs-master] for my application in (keil4.6/sdk8.0.0). Its already consisting (app_gpiote), but I want to add some code...
hello,
I am having some doubts regarding the connection handle. Will it be the same for both devices participating in a connection? I was trying to connect two devices, one...
A call to sd_ble_gatts_service_add(..) is returning fault code 0x3001. Looking at the NRF_ERROR #defines, this seems to mean "STK SVC handler is missing".
Can anyone shed...
Dear ladies and gentlemen,
I can't find this information anywhere. In the datasheet on page 519 - 521, I see that the decoupling capacitor C6 on pin 32 (DEC2) is not mounted...
Hi
Currently I have a device with the following details:
Ic Version - 2,
Variant - CE AA ,
Build Code - D0,
Hardware Id - 004d
I am using the softdevice s110_nrf51822_7...
I am trying to set up an environment based on CMSIS Packs. However, when using some components from nRF_Libraries, these lines get added to RTE_Components.h:
#define GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working on nrf51 iot sdk. I have created a IPv6 tunnel in HE and is able to ping the gateway as follows:
root@raspberrypi:/home/pi# ping6 2001:xxx:18:xxx::1
PING...
Hi,
I already used the sd_ble_uuid_vs_add for adding my base UUID in the internal table and it return a valid uuid_type (in my specific case it's 0x06).
I need to add...
I am using SDK 9.0.0 and i am having a doubt in bsp.h.In this header file when gone through this part of the code
#if (LEDS_NUMBER > 0) && !defined(BSP_SIMPLE)
#define...
For nrf 51 - DK , I flashed s130_nrf51_1.0.0_API
and then using keil uvision I copied over ble_app_uart_s130_pca_10028 and
tried to compile the code,
The code failed...
