When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I am new to nordic n51822, i have implemented adc and timer independently.
Now, what i want to do is read the adc values on a specific time when the timer overflows...
Received my nRF52 preview board yesterday and have been battling to get my S130 based nRF51 code running on it with the S132 soft device (the code is here: github.com/......
The codes i am using is
nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral and nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_peripheral\ble_app_hrs
From the peripheral...
Just getting started with the PCA10001. I can compile if I select the device nrf51822_xxaa_s110, but when I load it tells me "can't load flash device description".
It subsequently...
I have take the basic ble_app_hrs_with_timeslot and modified it to calculate the timing of subsequent calls to the timeslot START event.
Specifically,
take note...
Hello,
I'm trying to get the new SDK up and running on my OSX machine. I would like to make the blinky example work on my PCA10003. So, I copied the blinky/pca10028 folder...
Hello, Do you guys know if it is possible to generate a stable 38kHz signal using the Nordic?
I have been able to generate the required frequency however I am observing...
Not a question but thought worth mentioning.
developer.nordicsemi.com/.../
Good News
PWM library changes seems to have made it into the release.
Bad news:
Looks...
Hello,
I am working on an nRF51822 custom board application which is reading data from external sensor through TWI. It is based on the MPU6050 driver available in the SDK...
Hi there,
Before I asked this question, I have searched similar question about TWI example, but it seems there were some guys looking for such example as well. Not sure...
Hello
I try make a firmware update with nrf toolbox for iOS and i have a popup with "Please enable Service Changed Indication in your firmware".
In code, I have an error...
while I'm trying to compile my code, I got an error :
".\Objects\ble_firmware_v1.axf: Error: L6405E: No .ANY selector matches main.o(i.app_error_handler). "
this error...
I wonder if GPIO could safely be used for byte writes to the OUT port.
I have an 8bit (+control signals) peripheral connected to the GPIO and so far I was doing read-modify...
I will be using a 3.7V LiPo to power my NRF52 system. As far I understand, using the internal DCDC regulator is a better choice as it can save power compared to internal LDO...
