I have a single-ended signal that spans [0V,3.3V] and is centered around V_bias=1.65V (=3.3V/2).
I want to use the NRF54L internal gain to amplify only the AC parts of the...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi Team,
Iam doing project called automation of light using BLE technology.
Here Iam using sdk 12.1.0(ble_app_hrs_c) example for scanning or receiving and i flashed...
I have a small problem with my bootloader + application on NRF52832. I'm using SDK 12.2.0 with S132 v3.0.0.
When the device loses power, and power is then re-applied, the...
I'm using nRF52 + s132v2.0.0 + SDK11.0.0. I want to be able to update to s132v4.0.2 (or so) + SDK13.0.0 via DFU. I'm planning on modifying the bootloader start address to...
I'm using nRF52 + SDK11.0.0 + s132 and have a couple of questions on DFU.
I want to use a CMSIS-DAP programmer + OpenOCD to upload the bootloader (or BL+SD+APP+setting...
Hi,
I am using a nRF51822 board and I wanted to know if the LC filter is necessary if I don't need to use any analog entrance or exit. I just need the BLE and a digital...
Hello,
I was trying to load code in pca10028 and I started getting error as "No cortex M Sw device found".
It was working properly but later it started showing me this error...
Dear Nordicers,
I have an application where node based on s132 sofddevice 4.0.2 has multiple connections as a peripheral and as a central. The case is about non overlapping...
I have an NRF52832 DK [PCA10040, V1.1.0]. It used to do programming with it, but now it suddenly stop detecting as "JLink" in Windows, Linux and Mac. Now when I connect it...
Hi, I use the twi_master_using_app_twi_pca10040 (SDK 12.1) to test the TLC59116 LED module .
By changing the example project's code by referring the GitHub code, I have...
Hello the Nordic Team,
I come here after a lot of research and testing and do not understand what is going on in my program. (is it Embedded or iPhone nRF Toolbox side...
hi,
I follow the pwm routine, 51822 can work and output pwm, when I want to change the frequency of pwm encountered a problem, the program reset.
I use the method when i...
Hi,
I'm using Nrf51822 to implement a RTC(200ms tick)
I connect a external 16MHz crystal to the MCU.
I use the S110 softdevice with BLE function enabled, so it's in ble_stack_init...
Hey. Has anybody played with autocomplete for command line interface.
I like it alot and it is very helpfull. Now a autocomplete would be cool!
Here is what comes to mind...
How to setup a nRFDK52 as a central and nRF bluetooth kit as peripheral. Should I use nRF go studio? Do i need to load the soft device first before loading the app? What is...
