NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
Hey!
I am working on NRF51822-QFAC, with the help of SDK 12.2 with the aim of scanning my bluetooth speakers and mobile phone.
For the same, I have loaded the project...
I want to change rx to tx mode and back after recertion my master NRF24l01 packet on NRF52 with esb, how to do it?
I tried this but it doesnt works:
void nrf_esb_event_handler...
Hello,
I am using nrf51822 and supply is provided through rechargeable battery. Please review my schematic and suggest changes if there is any.
Thanks,
Shailav
I used the following code to verify the working of the clock (at P04) of nRF24le1.
I used a 4.7K pull up resistor with a VDD of 3.3V, which was output from the nRF.
Note...
Hello,
I'm using nrf51822/s130/sdk12.1.0.
Before adding BLE code there's no problem in writing inner flash.
In main I just added below ble_app_uart codes(not modified...
Hi,
I have Wireshark version 1.10.14 and sniffer version 1.0.1. I send the data out from PCA10040 with connection interval of 7.5 ms and packet throughput of 200Hz using...
The pulldown on the SAADC is 160k. Is it ok to create a resistor ladder by adding an external resistor of, say, 400k, enable the internal pulldown and then input a higher...
Hi NordicSemiconductor's community,
I have a basic question about connection to a BLE peripheral.
I use the SDK_10.0.0 and s110_v8.0.0.
I want to know how to implement...
how to change RX and TX operations ?
i wrote next code:
#include "nrf_esb.h"
#include <stdbool.h>
#include <stdint.h>
#include "sdk_common.h"
#include "nrf.h"
#include...
Hello
I used one example from the nrf52 SDK and wanted to add another functionality to the code. How do I know what to add to that file?
Is there a global sdk_config.h containing...
I am migrating from SDK 12.2 to SDK 13 on Nrf52.
I use Eclipse.
I have a few questions:
In SDK12.2, there was :
Patch for SDK 12 - implements required workaround...
i am using nrf52832 dk. i am trying to change the flash address from 0x000 to 0x0002000. But i can only flash it to 0x0002000 if softdevice is already present on controller...
