Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
I have a scenario in which hundreds of beacons are advertising. I want to know whether an observer can observe all the beacons or not. I have done a lot of search on this...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello!
I'm having trouble adding vendor specific UUID and configuring the memory. My service will require 3 vendor specific 128 bit UUID. One for the service and two for...
Hello,
I would like to make use of an Adafruit sensor Adafruit_TSL2591 connected to my nrf52 through the TWI interface. I have seen the example TWI master device, in that...
Hi,
My apology if this question has been answered. I wonder if >2mA current draw for an APP with the following design considered normal consumption?
Custom GATT profile...
Hi,
I'm using the UART to talk to a radio module with sdk 12.1 on nrf52.
I'm seeing frequent UART errors, where the event handler is called with event type APP_UART_COMMUNICATION_ERROR...
Some of you may be using the ARM compiler that Nordic provides with SDK 13.0. I was not able to install it on my PC as it does not want to install since it sees another other...
SDK 13.0.0
nrf_soc_nosd/nrf_nvic.h has this header guard:
#ifndef NRF_SOC_H__
#define NRF_SOC_H__
This means you couldn't include nrf_soc.h after including nrf_nvic...
Hello,
I'm using TIMER1 to generate a timer compare event. I connect the event with the sample task of the saadc like in the saadc example from the SDK. Everything works...
Hi,
While using the JLinkExe along with the JLinkRTTClient the RTT client eventually stops outputting messages.
After that, both the JLinkExe and the nrfjprog output...
Thank you for the support so far.
I want to ask that if for example in your system or product we want to add bluetooth headphone feature which support Bluetooth 4.0 headphones...
Hi,
I am new to Nordic product and I have NRF52 DK. I have started reading this document
www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit
However...
Hi,
I am trying to use the BLE v4.2 extended data length on the NRF51822 but the S130 doesn't seem to support it. Please can anyone let me know if it is supported with...
Hi,
I am trying to measure (and reduce) the current consumption of my board. I am using nrf52832 (64K RAM) for my development. The RAM layout is as follows: RAM (rwx) : ORIGIN...
Hello,
Is there any way to mitigate delay of redirecting interrupts from softdevice to application? Using nRF51 with S130 there is ~2us delay even with SoftDevice disabled...
